Discount applied at checkout
Accessories
Accessories
Filters
SKU 100-0113
Mounting bracket for G4+ & G4X Fury, Xtreme, Storm, Force (MTB1)
SKU 110-0005
Mounting bracket for G4+ & G4X Atom & Monsoon (MTB2)
SKU 135-9500B
Bundle - Includes 1 x Razor PDM and 1 x 12 Button CAN Keypad.
Link's highly anticipated PDM, the Razor PDM, is an intelligent Power Distribution Module that replaces traditional fuses and relays, putting you in complete control of your setup.
The Razor PDM is a programmable device that uses logic for the smart control of any outputs you have connected, meaning events and commands can be triggered when your vehicle hits specific parameters.
The device will allow you to manage things such as fuel pumps, radiator fans, electronic throttles, servos, lights and more, as well as monitoring analog or digital sensor signals.
You can gain full control by using an Analog Switch Panel, CAN Keypad or ECU to switch output channels, as well as increasing reliability and protecting your critical components from damage.
With superior thermal performance, the Razor PDM has been designed with vehicle protection in mind, while allowing for a more efficient, cleaner, and reliable build.
It may be small and compact, but the Razor PDM can handle up to 100 Amps of continuous combined current, as well as 160A of non-repetitive maximum current. If you need to manage even more power, you can easily add multiple Razor PDM’s via CAN or use as a CAN Expander to increase your inputs and outputs.
The Razor PDM has the ability to connect with many other ECU brands and CAN devices when using a custom CAN stream. Those of you with a Link ECU will be pleased to know that our software comes with a pre-configured stream, so your Link products will work with the device straight out of the box.
Setup and management of the Razor PDM is performed through our custom PDM Link software, which is free to download and use.
In the box:
• Link Razor PDM
• Mounting plate and screws
• Superseal C Plug and Pin Kit
• USB-C connection cable
• Positive terminal insulation boot
• 2 x high-current ring terminals and bolts
• Quickstart guide
SKU 135-9300B
Triple Bundle - Includes 3 x Razor PDMs.
Link's highly anticipated PDM, the Razor PDM, is an intelligent Power Distribution Module that replaces traditional fuses and relays, putting you in complete control of your setup.
The Razor PDM is a programmable device that uses logic for the smart control of any outputs you have connected, meaning events and commands can be triggered when your vehicle hits specific parameters.
The device will allow you to manage things such as fuel pumps, radiator fans, electronic throttles, servos, lights and more, as well as monitoring analog or digital sensor signals.
You can gain full control by using an Analog Switch Panel, CAN Keypad or ECU to switch output channels, as well as increasing reliability and protecting your critical components from damage.
With superior thermal performance, the Razor PDM has been designed with vehicle protection in mind, while allowing for a more efficient, cleaner, and reliable build.
It may be small and compact, but the Razor PDM can handle up to 100 Amps of continuous combined current, as well as 160A of non-repetitive maximum current. If you need to manage even more power, you can easily add multiple Razor PDM’s via CAN or use as a CAN Expander to increase your inputs and outputs.
The Razor PDM has the ability to connect with many other ECU brands and CAN devices when using a custom CAN stream. Those of you with a Link ECU will be pleased to know that our software comes with a pre-configured stream, so your Link products will work with the device straight out of the box.
Setup and management of the Razor PDM is performed through our custom PDM Link software, which is free to download and use.
In the box:
• Link Razor PDM
• Mounting plate and screws
• Superseal C Plug and Pin Kit
• USB-C connection cable
• Positive terminal insulation boot
• 2 x high-current ring terminals and bolts
• Quickstart guide
SKU 135-9200B
Bundle - Includes 2 x Razor PDMs.
Link's highly anticipated PDM, the Razor PDM, is an intelligent Power Distribution Module that replaces traditional fuses and relays, putting you in complete control of your setup.
The Razor PDM is a programmable device that uses logic for the smart control of any outputs you have connected, meaning events and commands can be triggered when your vehicle hits specific parameters.
The device will allow you to manage things such as fuel pumps, radiator fans, electronic throttles, servos, lights and more, as well as monitoring analog or digital sensor signals.
You can gain full control by using an Analog Switch Panel, CAN Keypad or ECU to switch output channels, as well as increasing reliability and protecting your critical components from damage.
With superior thermal performance, the Razor PDM has been designed with vehicle protection in mind, while allowing for a more efficient, cleaner, and reliable build.
It may be small and compact, but the Razor PDM can handle up to 100 Amps of continuous combined current, as well as 160A of non-repetitive maximum current. If you need to manage even more power, you can easily add multiple Razor PDM’s via CAN or use as a CAN Expander to increase your inputs and outputs.
The Razor PDM has the ability to connect with many other ECU brands and CAN devices when using a custom CAN stream. Those of you with a Link ECU will be pleased to know that our software comes with a pre-configured stream, so your Link products will work with the device straight out of the box.
Setup and management of the Razor PDM is performed through our custom PDM Link software, which is free to download and use.
In the box:
• Link Razor PDM
• Mounting plate and screws
• Superseal C Plug and Pin Kit
• USB-C connection cable
• Positive terminal insulation boot
• 2 x high-current ring terminals and bolts
• Quickstart guide
SKU 135-1000
Link's highly anticipated PDM, the Razor PDM, is an intelligent Power Distribution Module that replaces traditional fuses and relays, putting you in complete control of your setup.
The Razor PDM is a programmable device that uses logic for the smart control of any outputs you have connected, meaning events and commands can be triggered when your vehicle hits specific parameters.
The device will allow you to manage things such as fuel pumps, radiator fans, electronic throttles, servos, lights and more, as well as monitoring analog or digital sensor signals.
You can gain full control by using an Analog Switch Panel, CAN Keypad or ECU to switch output channels, as well as increasing reliability and protecting your critical components from damage.
With superior thermal performance, the Razor PDM has been designed with vehicle protection in mind, while allowing for a more efficient, cleaner, and reliable build.
It may be small and compact, but the Razor PDM can handle up to 100 Amps of continuous combined current, as well as 160A of non-repetitive maximum current. If you need to manage even more power, you can easily add multiple Razor PDM’s via CAN or use as a CAN Expander to increase your inputs and outputs.
The Razor PDM has the ability to connect with many other ECU brands and CAN devices when using a custom CAN stream. Those of you with a Link ECU will be pleased to know that our software comes with a pre-configured stream, so your Link products will work with the device straight out of the box.
Setup and management of the Razor PDM is performed through our custom PDM Link software, which is free to download and use.
In the box:
• Link Razor PDM
• Mounting plate and screws
• Superseal C Plug and Pin Kit
• USB-C connection cable
• Positive terminal insulation boot
• 2 x high-current ring terminals and bolts
• Quickstart guide
SKU 101-0054
Donut style 8mm Knock Sensor prewired with 2.6m loom, flying leads.
Suitable to wire directly to Link ECU or use with the G4 Knocklink Visual Warning Light.
SKU 114-2000
Kit includes the G4 KnockLink visual warning light and a knock sensor with loom. The KnockLink is a self-calibrating, visual knock warning tool. This kit is designed for tuning, street and race use.
The G4 KnockLink is the only detonation warning device on the market that requires no setup. Other systems require time consuming gain, frequency and noise settings to be adjusted. Without proper knock listening tools, this can prove difficult if not impossible. The KnockLink requires none of this, just wire in and start the engine.
Even light detonation will damage an engine over time. The G4 KnockLink's microprocessor continuously scans the knock signal and warns for any knock occurring. The engine's RPM and load is automatically 3D profiled by the KnockLink, continuously storing and dynamically adjusting this noise profile map while looking for the particular knock frequency.
Operation is simple. The colour of the LED represents four different modes:
Dim Blue - KnockLink is powered, waiting for the engine to be started
Flashing Blue - KnockLink has detected the engine has started and is now calibrating
Dim Green - KnockLink is adapting to the engine's noise profile and listening for knock
Flashing Red - KnockLink has detected knock. Avoid large throttle openings, seek professional advice
SKU 101-0287
Bosch Junior Timer / Jetronic (Male) to USCar (Female) Adapter
Commonly used when upgrading to fuel injectors with the newer USCar connector and your wiring loom has Bosch Junior Timer/Jetronic/EV1 connectors.
SKU 101-0288
Injector Adapter - USCar (Male) to Bosch Junior Timer/Jetronic (Female)
Fits Bosch Junior Timer/EV1/Jetronic injector and connects to USCar connector on the wiring loom.
SKU 101-0289
USCar Fuel Injector Connector Kit
Includes:
Housing
Crimp terminals
Terminal seals
Seal locating tab
Locking tab
SKU 101-0146 - 8Bundle
Extreme Duty Fast Response EGT Temperature Probe.
Bundle includes 8 x Probes.
Type K thermocouple probe
Exposed sensing junction for fastest response
Includes 316 SS adjustable compression fitting
Stainless steel protected wires
Designed for extreme engine test & racing environments
SKU 101-0146 - 4Bundle
Extreme Duty Fast Response EGT Temperature Probe.
This bundle includes four EGTs.
Type K thermocouple probe
Exposed sensing junction for fastest response
Includes 316 SS adjustable compression fitting
Stainless steel protected wires
Designed for extreme engine test & racing environments
SKU 101-0146
Extreme Duty Fast Response EGT Temperature Probe
Type K thermocouple probe
Exposed sensing junction for fastest response
Includes 316 SS adjustable compression fitting
Stainless steel protected wires
Designed for extreme engine test & racing environments
When using this with an ECU other than the Thunder, you will need to use an amplifier.
Specifications
Thermocouple type: K
Range: -148 to 2372°F (-100 to 1300°C)
Accuracy: +/-0.4% of reading or about +/- 1.1°C (Special Limits of Error)
Probe diameter: 1/4 inch (0.250 inch) (6.35 mm)
Sensing Junction: Exposed, Ungrounded
Response Time*: 150 mS
*Time Constant: Defined as the time required to reach 63.2% of an instantaneous temperature change
Five time constants are required to approach 100% of the step change value
Outer Sheath Material: Inconel, melting point 2550°F (1400°C)
Cable: Stainless steel overbraiding over Teflon™ insulated, stranded wires, 20 gauge. 6ft / 1.8m in length.
Compression Fitting: 316 stainless steel, adjustable, 1/8 inch –27 NPT male thread
Wiring: + = Yellow – = Red
SKU 101-0384
Link TCC04 4 Channel EGT to CAN module, powered by CANchecked
The TCC04 EGT to CAN module allows you to connect up to four Type-K thermocouples and send the values via CAN bus and/or monitor them directly on your wireless enabled device.
Type-K thermocouples are suitable for various applications such as measuring exhaust gas temperature (EGT), temperatures before/after the intercooler, turbo housings, cylinder head temperatures, water temperature, oil temperature and more. All measurements are cold junction compensated with a measuring range of 0 to 1250°C in 0.25°C resolution (14bit).
The TCC04 feature a four-pin DTM connector for CAN & power that is pin compatible with Links standard CAN pinout and CAN cables range. CAN 2.0A/B standard is supported with flexible configuration.
Wireless connectivity allows you to configure and update your module via smartphone or PC and query the current temperature and thermocouple status.
Features:
- 4 x cold junction compensated type-K inputs
- CAN Bus connection to ECU (Pre-Configured for Link ECU)
- Measuring range from 0 to 1250°C (32 to 2282°F) with 0.25°C resolution
- Detection of short circuit to ground or if no type-K is connected
- Standard mini k thermocouple connector
- Full configuration and monitoring over wireless
- Adjustable sample frequency up to 100Hz
Box Contents:
1 x CAN EGT Module
1 x DTM4 Mating Connector Kit
2 x Link Stickers
SKU 101-0386
Link TCC06 6 Channel EGT to CAN module, powered by CANchecked
The TCC06 EGT to CAN module allows you to connect up to six Type-K thermocouples and send the values via CAN bus and/or monitor them directly on your wireless enabled device.
Type-K thermocouples are suitable for various applications such as measuring exhaust gas temperature (EGT), temperatures before/after the intercooler, turbo housings, cylinder head temperatures, water temperature, oil temperature and more. All measurements are cold junction compensated with a measuring range of 0 to 1250°C in 0.25°C resolution (14bit).
The TCC06 feature a four-pin DTM connector for CAN & power that is pin compatible with Links standard CAN pinout and CAN cables range. CAN 2.0A/B standard is supported with flexible configuration.
Wireless connectivity allows you to configure and update your module via smartphone or PC and query the current temperature and thermocouple status.
Features:
- 6 x cold junction compensated type-K inputs
- CAN Bus connection to ECU (Pre-Configured for Link ECU)
- Measuring range from 0 to 1250°C (32 to 2282°F) with 0.25°C resolution
- Detection of short circuit to ground or if no type-K is connected
- Standard mini k thermocouple connector
- Full configuration and monitoring over wireless
- Adjustable sample frequency up to 100Hz
Box Contents:
1 x CAN EGT Module
1 x DTM4 Mating Connector Kit
2 x Link Stickers
SKU 101-0388
Link TCC08 8 Channel EGT to CAN module, powered by CANchecked
The TCC08 EGT to CAN module allows you to connect up to eight Type-K thermocouples and send the values via CAN bus and/or monitor them directly on your wireless enabled device.
Type-K thermocouples are suitable for various applications such as measuring exhaust gas temperature (EGT), temperatures before/after the intercooler, turbo housings, cylinder head temperatures, water temperature, oil temperature and more. All measurements are cold junction compensated with a measuring range of 0 to 1250°C in 0.25°C resolution (14bit).
The TCC08 feature a four-pin DTM connector for CAN & power that is pin compatible with Links standard CAN pinout and CAN cables range. CAN 2.0A/B standard is supported with flexible configuration.
Wireless connectivity allows you to configure and update your module via smartphone or PC and query the current temperature and thermocouple status.
Features:
8 x cold junction compensated type-K inputs
CAN Bus connection to ECU (Pre-Configured for Link ECU)
Measuring range from 0 to 1250°C (32 to 2282°F) with 0.25°C resolution
Detection of short circuit to ground or if no type-K is connected
Standard mini k thermocouple connector
Full configuration and monitoring over wireless
Adjustable sample frequency up to 100Hz
Box Contents:
1 x CAN EGT Module
1 x DTM4 Mating Connector Kit
2 x Link Stickers
SKU 101-0044
This three channel igniter is suitable for electronic ignition applications. Required when using coils that don't have inbuilt igniters.
Common uses include: wasted spark on 6 cylinder engines, coil-per-plug setups on 3 cylinder engines or using multiple igniters for 6 and 8 cylinder set-ups.
Compatible with all Link Wire-in ECU’s.
Includes heatsinking compound, 7 pin plug, pins and boot.
Note - Does not include heatsink
SKU 101-0291
High Power Inductive Coil with built-in ignitor.
Produce 103 mJ per spark, with a longer spark duration (2.9 ms) than what you’d see with a capacitive discharge
Built-in ignitor with external heat sink
Requires HEI-type plug wire ends/ boots. Compatible with most brands of HT lead
Box Contents
1 x IGN1A Smart Coil
1 x Mating Connector Kit
Link to User Guide
SKU 101-0060
To suit G1 / G2 LinkPlus models, 2m
SKU 115-1000
Link's external E-throttle (Drive by Wire) module works with Link's G4X ECUs (except the entry level AtomX), plus G4+ ECUs (Storm and above) to give you full control of your throttle setup, allowing a faster more precise throttle response.
Replace your old mechanical throttle linkage with an advanced electronic throttle module. E-throttle is faster responding, requires less maintenance, gives you better fuel economy and lowers emissions.
The Remote E-throttle module is designed to be used with any Link G4X ECU (except the entry level AtomX) and any Link G4+ ECU (Storm and above). It is most commonly used to provide e-throttle control to the MonsoonX, StormX or PlugINX ECUs or secondary E-throttle control to the XtremeX or FuryX ECUs.
SKU 101-0188
E-Throttle Accelerator Pedal Module
Firewall mounted hanging design
16degree (~70mm) travel
Redundant dual output potentiometers suitable for use with Electronic throttle bodies
Includes 6 pin mating connector kit
Pin 1 = 5V Pin 2 = 5V Pin 3 = Sensor Ground Pin 4 = AP Main Output Pin 5 = Sensor Ground Pin 6 = AP Sec Output
SKU 101-0190
82mm Electronic Throttle Body
82mm Bore size
Dual potentiometer redundancy
Bosch quality and performance
Includes groove on inlet port flange
Includes mating connector kit
SKU 101-0194
74mm Electronic Throttle Body
74mm Bore size
Dual potentiometer redundancy
Bosch quality and performance
Includes groove on inlet port flange
Includes mating connector kit
SKU 101-0106
Want to add additional inputs/output to your Link Plugin ECU? Use the XS Loom. The Link XS Loom plugs into the expansion connector on all Link G4, G4+ and G4X plug-in ECUs. The number of extra inputs and outputs added by the XS Loom is dependent on the Plugin ECU. For specific details check the plug-in ECUs specifications.
Common applications include but are not limited to:
Boost adjustment knob or switch
Wide-band AFR/Lambda
Oil Pressure Sensor
Fuel Pressure Sensor
Inlet Air Temperature (IAT) sensor
Map switch (Different tunes available via toggle switch)
The XS Loom is 2.5m long and uses 20AWG wire.
SKU 101-0009
5 m long 'B' loom to suit G4, G4+ and G4X ECUs
Perfect for all custom wiring jobs utilising Link WireIn ECUs. The ‘B’ Loom has a Link ‘B’ ECU connector at one end and unterminated wires at the other. All wires are colour coded to match the manual. This loom is also available in 0.4m and 2.5m lengths.
Added features of 2.5m and 5m ‘B’ Looms include:
-Shielded Dual Core wires for knock signals
Suitable for:
Link G4X Storm (Loom A also required)
Link G4X and G4+ Fury (Loom A also required)
Link G4X, G4+ and G4 Xtreme (Loom A also required)
Link G4+ Thunder (Note: Loom A and connector kits C and D may also be required)
Link G4+ Storm Black (Loom A also required) – Note: Loom B is not required for the older Silver or Blue G4 or G4+ Storm models
Vipec V88 (Loom A also required)
Vipec i88 (Loom A also required)
SKU 101-0006
2.5 m long 'B' loom to suit G4, G4+ and G4X ECUs
Perfect for all custom wiring jobs utilising Link WireIn ECUs. The ‘B’ Loom has a Link ‘B’ ECU connector at one end and unterminated wires at the other. All wires are colour coded to match the manual. This loom is also available in 0.4m and 5m lengths.
Added features of 2.5m and 5m ‘B’ Looms include:
-Shielded Dual Core wires for knock signals
Suitable for:
Link G4X Storm (Loom A also required)
Link G4X and G4+ Fury (Loom A also required)
Link G4X, G4+ and G4 Xtreme (Loom A also required)
Link G4+ Thunder (Note: Loom A and connector kits C and D may also be required)
Link G4+ Storm Black (Loom A also required) – Note: Loom B is not required for the older Silver or Blue G4 or G4+ Storm models
Vipec V88 (Loom A also required)
Vipec i88 (Loom A also required)
SKU 101-0003
0.4m long 'B' loom to suit G4, G4+ and G4X Wire-In ECUs
Perfect for all custom wiring jobs utilising Link WireIn ECUs. The ‘B’ Loom has a Link ‘B’ ECU connector at one end and unterminated wires at the other. All wires are colour coded to match the manual. This loom is also available in 2.5m and 5m lengths.
Suitable for:
Link G4X Storm (Loom A also required)
Link G4X and G4+ Fury (Loom A also required)
Link G4X, G4+ and G4 Xtreme (Loom A also required)
Link G4+ Thunder (Note: Loom A and connector kits C and D may also be required)
Link G4+ Storm Black (Loom A also required) – Note: Loom B is not required for the older Silver or Blue G4 or G4+ Storm models
Vipec V88 (Loom A also required)
Vipec i88 (Loom A also required)
SKU 101-0008
5 m long 'A' loom to suit G4, G4+ and G4X ECUs
Perfect for all custom wiring jobs utilising Link WireIn ECUs. The ‘A’ Loom has a Link ‘A’ ECU connector at one end and unterminated wires at the other. All wires are colour coded to match the manual. This loom is also available in 0.4m and 2.5m lengths.
Added features of 2.5m and 5m ‘A’ Looms include:
- Shielded Dual Core wires for trigger signals
- Added ground and 5V wires spliced in with labels suggesting pin use
Suitable for:
All Link G4X WireIn ECU’s (Note: Loom B will also be required for the Storm/Fury/Xtreme)
Link G4+ Atom (NB: Does NOT suit the earlier G4 Atom models. I.e. G4+ only)
Link G4+ Atom II
Link G4+ Monsoon
Link G4 Storm
Link G4+ Storm Blue
Link G4+ Storm Black (Note: Loom B will also be required)
Link G4 RX
Link G4+ Fury (Note: Loom B will also be required)
Link G4 Xtreme (Note: Loom B will also be required)
Link G4+ Xtreme (Note: Loom B will also be required)
Link G4+ Thunder (Note: Loom B and connector kits C and D may also be required)
Vipec V44
Vipec i44
Vipec V88 (Note: Loom B will also be required)
Vipec i88 (Note: Loom B will also be required)
SKU 101-0005
2.5 m long 'A' loom to suit G4, G4+ and G4X ECUs
Perfect for all custom wiring jobs utilising Link WireIn ECUs. The ‘A’ Loom has a Link ‘A’ ECU connector at one end and unterminated wires at the other. All wires are colour coded to match the manual. This loom is also available in 0.4m and 5m lengths.
Added features of 2.5m and 5m ‘A’ Looms include:
-Shielded Dual Core wires for trigger signals
-Added ground and 5V wires spliced in with labels suggesting pin use
Suitable for:
All Link G4X WireIn ECU’s (Note: Loom B will also be required for the Storm/Fury/Xtreme)
Link G4+ Thunder (Note: Loom B and connector kits C and D may also be required)
Link G4+ Atom (NB: Does NOT suit the earlier G4 Atom models. I.e. G4+ only)
Link G4+ Atom II
Link G4+ Monsoon
Link G4 Storm
Link G4+ Storm Blue
Link G4+ Storm Black (Note: Loom B will also be required)
Link G4 RX
Link G4+ Fury (Note: Loom B will also be required)
Link G4 Xtreme (Note: Loom B will also be required)
Link G4+ Xtreme (Note: Loom B will also be required)
Vipec V44
Vipec i44
Vipec V88 (Note: Loom B will also be required)
Vipec i88 (Note: Loom B will also be required)
SKU 101-0002
0.4m long 'A' loom to suit G4, G4+ and G4X Wire-In ECUs
Perfect for all custom wiring jobs utilising Link WireIn ECUs. The ‘A’ Loom has a Link ‘A’ ECU connector at one end and unterminated wires at the other. All wires are colour coded to match the manual. This loom is also available in 2.5m and 5m lengths.
Suitable for:
All Link G4X WireIn ECU’s (Note: Loom B will also be required for the Storm/Fury/Xtreme)
Link G4+ Atom (NB: Does NOT suit the earlier G4 Atom models. I.e. G4+ only)
Link G4+ Atom II
Link G4+ Monsoon
Link G4 Storm
Link G4+ Storm Blue
Link G4+ Storm Black (Note: Loom B will also be required)
Link G4 RX
Link G4+ Fury (Note: Loom B will also be required)
Link G4 Xtreme (Note: Loom B will also be required)
Link G4+ Xtreme (Note: Loom B will also be required)
Link G4+ Thunder (Note: Loom B and connector kits C and D may also be required)
Vipec V44
Vipec i44
Vipec V88 (Note: Loom B will also be required)
Vipec i88 (Note: Loom B will also be required)
SKU 101-0033
Dual core screen cable for use with trigger signals and knock sensors - 10m per pack
SKU 101-0311
50m pack of Automotive Wire (4 colours).
20m x Red
10m x Black
10m x Red/Green
10m x Green
Wire Spec: AVSS Thinwall 0.5mm² (20 AWG)
SKU 101-0131
Deutsch 2 Way Plug Kit
SKU 101-0225
Deutsch DTM4 Connector Kit (Female) to suit Link CAN Bus connections. Use to connect CAN devices into Link CAN bus.
Includes Female Housing (Receptacle), Wedgelock & Pins
SKU 101-0051
Bosch 2 way plug kit. Useful for a variety of applications. Most commonly paired with Bosch Fuel Injectors.
Includes 2 way Bosch Style Plug, pins and rubber boot
SKU 101-0029
Bosch 3 Way Plug Kit
SKU 101-0030
7 way Bosch Style Plug, pin and Boot
SKU 101-0124
Blanking plugs for unused terminal positions - 100 pack. Suits A, B, C and D G4, G4+ and G4X ECU connectors.
SKU 101-0123
Blanking plugs for unused terminal positions - 20 pack. Suits A, B, C and D G4, G4+ and G4X ECU connectors
SKU 101-0293
Plug and Pin Kit only, E Plug. Includes:
1 x 26 position Superseal Connector Housing "E Plug"
26 x Superseal Terminals Gold Contact Finish “Pins”
Suitable for:
G5 Voodoo Pro (26 pin E Connector)
SKU 101-0097
Equivalent plug and connectors as "B" Loom. Plug and Pin Kit only.
Suitable for:
Link G4X Storm (Loom A/Pin Kit A also required)
Link G4X and G4+ Fury (Loom A/Pin Kit A also required)
Link G4X, G4+ and G4 Xtreme (Loom A/Pin Kit A also required)
Link G4+ Thunder (Note: Loom A/Pin Kit A and connector kits C and D may also be required)
Link G4+ Storm Black (Loom A/Pin Kit A also required) – Note: Loom B is not required for the older Silver or Blue G4 or G4+ Storm models
Vipec V88 (Loom A/Pin Kit A also required)
Vipec i88 (Loom A/Pin Kit A also required)
SKU 101-0096
Equivalent plug and connectors as "A" Loom. Plug and Pin Kit only.
Suitable for:
All Link G4X WireIn ECU’s (Note: Loom B/Pin Kit B will also be required for the Storm/Fury/Xtreme)
Link G4+ Atom (NB: Does NOT suit the earlier G4 Atom models. I.e. G4+ only)
Link G4+ Atom II
Link G4+ Monsoon
Link G4 Storm
Link G4+ Storm Blue
Link G4+ Storm Black (Note: Loom B/Pin Kit B will also be required)
Link G4 RX
Link G4+ Fury (Note: Loom B/Pin Kit B will also be required)
Link G4 Xtreme (Note: Loom B/Pin Kit B will also be required)
Link G4+ Xtreme (Note: Loom B/Pin Kit B will also be required)
Link G4+ Thunder (Note: Loom B/Pin Kit B and connector kits C and D may also be required)
Vipec V44
Vipec i44
Vipec V88 (Note: Loom B/Pin Kit B will also be required)
Vipec i88 (Note: Loom B/Pin Kit B will also be required)
SKU 101-0119
Housing and 26 terminals for C connector. Plug and Pin Kit Only.
Suitable for:
G4+ Thunder
Obsolete G4 Atom and Lightning. (Not G4+ or G4X Atom)
SKU 101-0120
Housing and 26 terminals for D connector. Plug and Pin kit only.
Suitable for:
G4+ Thunder
SKU 101-0121
Terminals - 100 pack. Suits A, B, C and D G4, G4+ and G4X ECU connectors.
SKU 101-0122
Terminals - 20 pack. Suits A, B, C and D G4, G4+ and G4X ECU connectors.
SKU 101-0095
G3 LinkPlus models. 74 way housing
SKU 101-0094
To suit G3 LEM models only. 26 way housing and terminals
SKU 101-0092
To suit G1 models. 17 way housing and terminals
SKU 101-0286
Includes housings, wedgelocks and pins. 7.5A
SKU 101-0285
Includes housings, wedgelocks and pins. 7.5A
SKU 101-0284
Includes housings, wedgelocks and pins. 7.5A
SKU 101-0283
Includes housings, wedgelocks and pins. 7.5A
SKU 101-0282
Includes housings, wedgelocks and pins. 7.5A
SKU 101-0281
Includes housings, wedgelocks and pins. 7.5A
SKU 101-0229
Crimping Tool for terminals to suit AMP Superseal connectors. To suit terminals used in A, B, C and D loom connectors.
SKU 100-0170
Add-on GPS module for the MXS and MXG Strada Dashes. 1.3m cable length.
Features:
Sample lap and split times as well as speed, position and acceleration - all the information needed for engine tuning as well as for improving your driving technique.
Supports more than 2000 tracks worldwide
Easy to set-up and review data using Race Studio 3
Connects to dual satellites for redundancy and precision
Simple, plug and play connection to Strada MXS & MXG Dashes
A GPS module also provides the dash with a speed signal. This can be particularly useful for applications where wheel speeds are not available or utilised, such as boats.
Specifications
Dimensions: 64.8 x 53.2 x 19.7 mm, Weight: 60.5 g
You do not need to configure anything before going to the track: GPS09 will do it all by itself.
Satellite signal is locked very rapidly. A few seconds after switch-on, the GPS09 is ready to operate
An average of less than one meter tolerance, which means absolute precision in determining vehicle position in curves and when the finish line is very close to another track segment
SKU 101-0299
Used to increase Wi-Fi signal strength. Glass Mount. 3m Cable.
Compatible with G5 Voodoo Pro.
SKU 101-0312
10m 4 Core CAN Wiring. Useful for wiring in CAN Accessories.
Four internal wires (White, Green, Red, Black) in a PVC outer jacket.
Internal Wire Spec: FLRRY 0.5mm² (20 AWG)
Outer Jacket Sepc: PVC, OD 6.1mm
SKU 101-0104
USB Mini Cable. Used to connect ECU to computer for tuning.
Suitable for:
G4X Atom
G4X Monsoon
G4+ Atom
G4+ Kurofune
G4+ Monsoon
SKU 101-0001
Link CAN to USB Tuning Cable. Used to connect the ECU to a computer via USB. A CAN to Serial cable is also available.
Compatible with:
Link G4X Storm
Link G4X and G4+ Fury
Link G4X and G4+ Xtreme
Link G4+ Thunder
All Link G4+ and G4X Plugin ECUs
Link G4+ Storm Black/Blue/Silver
Any older Link ECU utilising the Link 6 Pin CAN connector
Vipec V88 and i44
Link G3
SKU 101-0023
Link CAN to Serial (DB9 Female connector) Tuning Cable. Used to connect ECU to a computer with a serial interface (DB9 Male). A USB tuning cable is also available.
Compatible with:
Link G4X Storm
Link G4X and G4+ Fury
Link G4X and G4+ Xtreme
Link G4+ Thunder
Link G4+ Storm Black
Link G4+ and G4X Plugin ECUs
Any older Link ECU utilising the Link 6 Pin CAN connector
SKU 101-0022
Required to add CAN/Serial communications to G4+/G4X Plugin ECU’s. Plugs directly into ECU PCB header. Use the Link CANF connector (purchased separately) to connect.
SKU 101-0020
Field Installable CAN Plug - Can be used to wire in to the 6 pin CAN port on Link G4/G4+/G4X ECUs that have a round 6 pin CAN communication port. Requires soldering for assembly.
Also see CANLTW - CAN Connection Cable for WireIn ECU’s (6Pin CAN)
SKU 101-0214
2 meter CAN Extension Cable for increased reach between your ECU CAN cable and CAN splitter/s or CAN device/s.
Specs
DTM4 Female to DTM4 Male. Includes CAN and Power Wiring.
Length: 2 metres
DTM4 Pin Out
Pin 4: CAN H
Pin 3: CAN L
Pin 2: Ground
Pin 1: 12V
SKU 101-0210
Required to add CAN communication to WireIn ECU's which have CAN accessible via the Header.
Compatible ECU's:
G4X/G4+ Atom (CAN1)
G4X/G4+ Monsoon (CAN1)
G4X/G4+ Storm (CAN2)
G4X/G4+ Xtreme (CAN2)
G4X/G4+ Fury (CAN2)
G5 Voodoo Pro (CAN1)
G4+ Force (CAN2)
G4+ Thunder (CAN2)
Specs
DTM4 Male to Flying leads. CAN H & L crimped with Superseal terminals. 12V & GND Flying Leads. Length: CAN Loom length 300mm (Flying leads 500mm long)
DTM4 Pin Out
Pin 4: CAN H
Pin 3: CAN L
Pin 2: Ground
Pin 1: 12V
SKU 101-0197
Used to add CAN communications to G4+/G4X Plugin ECU’s which have a 5 Pin CAN connector. Plugs directly into the CAN socket on the ECU PCB. 12V and Ground via flying lead. Terminates to a DTM4 Male Connector which is compatible with other Link CAN accessories including the CAN Extension cable (CANEXT) and CAN Splitter Cable (CANTEE)
Not compatible with the below PlugIns (these require a CANJST4 Cable):
214-4100 - PlugIn ECU G4X Nissan GTR with E-Throttle
217-4100 - PlugIn ECU G4X Nissan S15 with E-Throttle
233-4000 - PlugIn ECU G4X Honda S2000 AP1
228-4000 - PlugIn ECU G4X Subaru WRX V5-6
237-4000 - PlugIn ECU G4X Honda HC20X Type-R DC5/RSX
238-4000 - Plugin ECU G4X Subaru WRX11
239-4000 - Plugin ECU G4X MX5NB2X
240-4000 - Plugin ECU G4X MX5NB1X
243-4000 - Plugin ECU G4X WRX11 USDM
Specs
DTM4 Male to JST4. 12V and GND Terminated to JST5. Length 300mm
DTM4 Pin Out
Pin 4: CAN H
Pin 3: CAN L
Pin 2: Ground
Pin 1: 12V
SKU 101-0198
Required to add CAN communications & power to recently released G4X Plugin ECU’s which have the new 4 Pin powered CAN connector (not the older 5pin CAN connector). Plugs directly into the socket on the ECU PCB, provides CAN and a protected 12V supply to allow easy connection of CAN accessories.
Suitable for powering a CAN Lambda, Dash, EGT amplifier or other similar low powered CAN devices which have a total continuous current draw of <3A.
Compatible PlugIns:
214-4100 - PlugIn ECU G4X Nissan GTR with E-Throttle
217-4100 - PlugIn ECU G4X Nissan S15 with E-Throttle
233-4000 - PlugIn ECU G4X Honda S2000 AP1
228-4000 - PlugIn ECU G4X Subaru WRX V5-6
237-4000 - PlugIn ECU G4X Honda HC20X Type-R DC5/RSX
238-4000 - Plugin ECU G4X Subaru WRX11
239-4000 - Plugin ECU G4X MX5NB2X
240-4000 - Plugin ECU G4X MX5NB1X
243-4000 - Plugin ECU G4X WRX11 USDM
Specs
DTM4 Male to JST4. 12V and GND Terminated to JST4. Length 300mm
DTM4 Pin Out
Pin 4: CAN H
Pin 3: CAN L
Pin 2: Ground
Pin 1: 12V
SKU 101-0211
Required to add CAN communication to WireIn ECU's which have CAN accessible via the 6Pin round CAN connector on the front of the ECU.
Compatible ECU's:
G5 Voodoo Pro (CAN1)
G4X/G4+ Xtreme (CAN1)
G4X/G4+ Fury (CAN1)
G4+ Force (CAN1)
G4+ Thunder (CAN1)
Specs
DTM4 Male to LTW 6Pin. 12V & GND Flying Leads. CAN Loom Length 300mm (Flying lead length 500mm)
DTM4 Pin Out
Pin 4: CAN H
Pin 3: CAN L
Pin 2: Ground
Pin 1: 12V
SKU 101-0212
CAN Splitter Cable for connecting an additional CAN devices.
Use to connect from a CANJST, CANLTW or CANSS into 2 CAN devices.
Specs
DTM4 Female to 2 x DTM4 Male. Includes CAN and Power Wiring.
Loom 1 Length: 80mm
Loom 2 Length: 120mm
DTM4 Pin Out
Pin 4: CAN H
Pin 3: CAN L
Pin 2: Ground
Pin 1: 12V
SKU 101-0283
Includes housings, wedgelocks and pins. 7.5A
SKU 101-0225
Deutsch DTM4 Connector Kit (Female) to suit Link CAN Bus connections. Use to connect CAN devices into Link CAN bus.
Includes Female Housing (Receptacle), Wedgelock & Pins
Special Order Parts
Parts Available but will need sales representative assistance.
Special shipping/part fitment
Click HERE or on any image to request a quote for any part you do not see on the website.
We will be adding more parts to the website daily so check back for new inventory.