Discount applied at checkout
Sensors/Controllers
Sensors/Controllers
Filters
SKU 101-0034
Looking to run flex-fuel? Then the Ethanol Content Sensor is a must have. The Ethanol Content Sensor measures the ratio of ethanol to petrol in a flex fuel vehicle. This sensor also measures fuel temperature. Compatible with all current Link Wire-In and Plug-In ECU’s. Uses 1 Digital input on the ECU. The sensor is fitted to the vehicle’s fuel return line anywhere between the fuel pressure regulator and the fuel tank.
AN-6 Fittings
Includes plug and pin kit
Technical Specs
The pinout is indicated on the sensor itself (from left to right looking into connector on sensor) as :
1.) Vcc (+12V supply)
2.) GND (ground)
3.) Vout (digital signal out)
SKU 135-9500B
Bundle - Includes 1 x Razor PDM and 1 x 12 Button CAN Keypad.
Link's highly anticipated PDM, the Razor PDM, is an intelligent Power Distribution Module that replaces traditional fuses and relays, putting you in complete control of your setup.
The Razor PDM is a programmable device that uses logic for the smart control of any outputs you have connected, meaning events and commands can be triggered when your vehicle hits specific parameters.
The device will allow you to manage things such as fuel pumps, radiator fans, electronic throttles, servos, lights and more, as well as monitoring analog or digital sensor signals.
You can gain full control by using an Analog Switch Panel, CAN Keypad or ECU to switch output channels, as well as increasing reliability and protecting your critical components from damage.
With superior thermal performance, the Razor PDM has been designed with vehicle protection in mind, while allowing for a more efficient, cleaner, and reliable build.
It may be small and compact, but the Razor PDM can handle up to 100 Amps of continuous combined current, as well as 160A of non-repetitive maximum current. If you need to manage even more power, you can easily add multiple Razor PDM’s via CAN or use as a CAN Expander to increase your inputs and outputs.
The Razor PDM has the ability to connect with many other ECU brands and CAN devices when using a custom CAN stream. Those of you with a Link ECU will be pleased to know that our software comes with a pre-configured stream, so your Link products will work with the device straight out of the box.
Setup and management of the Razor PDM is performed through our custom PDM Link software, which is free to download and use.
In the box:
• Link Razor PDM
• Mounting plate and screws
• Superseal C Plug and Pin Kit
• USB-C connection cable
• Positive terminal insulation boot
• 2 x high-current ring terminals and bolts
• Quickstart guide
SKU 135-9300B
Triple Bundle - Includes 3 x Razor PDMs.
Link's highly anticipated PDM, the Razor PDM, is an intelligent Power Distribution Module that replaces traditional fuses and relays, putting you in complete control of your setup.
The Razor PDM is a programmable device that uses logic for the smart control of any outputs you have connected, meaning events and commands can be triggered when your vehicle hits specific parameters.
The device will allow you to manage things such as fuel pumps, radiator fans, electronic throttles, servos, lights and more, as well as monitoring analog or digital sensor signals.
You can gain full control by using an Analog Switch Panel, CAN Keypad or ECU to switch output channels, as well as increasing reliability and protecting your critical components from damage.
With superior thermal performance, the Razor PDM has been designed with vehicle protection in mind, while allowing for a more efficient, cleaner, and reliable build.
It may be small and compact, but the Razor PDM can handle up to 100 Amps of continuous combined current, as well as 160A of non-repetitive maximum current. If you need to manage even more power, you can easily add multiple Razor PDM’s via CAN or use as a CAN Expander to increase your inputs and outputs.
The Razor PDM has the ability to connect with many other ECU brands and CAN devices when using a custom CAN stream. Those of you with a Link ECU will be pleased to know that our software comes with a pre-configured stream, so your Link products will work with the device straight out of the box.
Setup and management of the Razor PDM is performed through our custom PDM Link software, which is free to download and use.
In the box:
• Link Razor PDM
• Mounting plate and screws
• Superseal C Plug and Pin Kit
• USB-C connection cable
• Positive terminal insulation boot
• 2 x high-current ring terminals and bolts
• Quickstart guide
SKU 135-9200B
Bundle - Includes 2 x Razor PDMs.
Link's highly anticipated PDM, the Razor PDM, is an intelligent Power Distribution Module that replaces traditional fuses and relays, putting you in complete control of your setup.
The Razor PDM is a programmable device that uses logic for the smart control of any outputs you have connected, meaning events and commands can be triggered when your vehicle hits specific parameters.
The device will allow you to manage things such as fuel pumps, radiator fans, electronic throttles, servos, lights and more, as well as monitoring analog or digital sensor signals.
You can gain full control by using an Analog Switch Panel, CAN Keypad or ECU to switch output channels, as well as increasing reliability and protecting your critical components from damage.
With superior thermal performance, the Razor PDM has been designed with vehicle protection in mind, while allowing for a more efficient, cleaner, and reliable build.
It may be small and compact, but the Razor PDM can handle up to 100 Amps of continuous combined current, as well as 160A of non-repetitive maximum current. If you need to manage even more power, you can easily add multiple Razor PDM’s via CAN or use as a CAN Expander to increase your inputs and outputs.
The Razor PDM has the ability to connect with many other ECU brands and CAN devices when using a custom CAN stream. Those of you with a Link ECU will be pleased to know that our software comes with a pre-configured stream, so your Link products will work with the device straight out of the box.
Setup and management of the Razor PDM is performed through our custom PDM Link software, which is free to download and use.
In the box:
• Link Razor PDM
• Mounting plate and screws
• Superseal C Plug and Pin Kit
• USB-C connection cable
• Positive terminal insulation boot
• 2 x high-current ring terminals and bolts
• Quickstart guide
SKU 135-1000
Link's highly anticipated PDM, the Razor PDM, is an intelligent Power Distribution Module that replaces traditional fuses and relays, putting you in complete control of your setup.
The Razor PDM is a programmable device that uses logic for the smart control of any outputs you have connected, meaning events and commands can be triggered when your vehicle hits specific parameters.
The device will allow you to manage things such as fuel pumps, radiator fans, electronic throttles, servos, lights and more, as well as monitoring analog or digital sensor signals.
You can gain full control by using an Analog Switch Panel, CAN Keypad or ECU to switch output channels, as well as increasing reliability and protecting your critical components from damage.
With superior thermal performance, the Razor PDM has been designed with vehicle protection in mind, while allowing for a more efficient, cleaner, and reliable build.
It may be small and compact, but the Razor PDM can handle up to 100 Amps of continuous combined current, as well as 160A of non-repetitive maximum current. If you need to manage even more power, you can easily add multiple Razor PDM’s via CAN or use as a CAN Expander to increase your inputs and outputs.
The Razor PDM has the ability to connect with many other ECU brands and CAN devices when using a custom CAN stream. Those of you with a Link ECU will be pleased to know that our software comes with a pre-configured stream, so your Link products will work with the device straight out of the box.
Setup and management of the Razor PDM is performed through our custom PDM Link software, which is free to download and use.
In the box:
• Link Razor PDM
• Mounting plate and screws
• Superseal C Plug and Pin Kit
• USB-C connection cable
• Positive terminal insulation boot
• 2 x high-current ring terminals and bolts
• Quickstart guide
SKU 101-0054
Donut style 8mm Knock Sensor prewired with 2.6m loom, flying leads.
Suitable to wire directly to Link ECU or use with the G4 Knocklink Visual Warning Light.
SKU 114-2000
Kit includes the G4 KnockLink visual warning light and a knock sensor with loom. The KnockLink is a self-calibrating, visual knock warning tool. This kit is designed for tuning, street and race use.
The G4 KnockLink is the only detonation warning device on the market that requires no setup. Other systems require time consuming gain, frequency and noise settings to be adjusted. Without proper knock listening tools, this can prove difficult if not impossible. The KnockLink requires none of this, just wire in and start the engine.
Even light detonation will damage an engine over time. The G4 KnockLink's microprocessor continuously scans the knock signal and warns for any knock occurring. The engine's RPM and load is automatically 3D profiled by the KnockLink, continuously storing and dynamically adjusting this noise profile map while looking for the particular knock frequency.
Operation is simple. The colour of the LED represents four different modes:
Dim Blue - KnockLink is powered, waiting for the engine to be started
Flashing Blue - KnockLink has detected the engine has started and is now calibrating
Dim Green - KnockLink is adapting to the engine's noise profile and listening for knock
Flashing Red - KnockLink has detected knock. Avoid large throttle openings, seek professional advice
sku 101-0053
Donut style
8mm hole
Includes plug and pin kit
SKU 125-1000
Link’s CAN Lambda is an easy to use CAN module that provides digital wideband sensor control via CAN bus and is compatible with leading aftermarket ECUs.
If using the CAN Lambda with a G4+/G4X PlugIn ECU use a Link CANPCB cable to access the CAN port on the PlugIn PCB and a Link CANF field insertable CAN plug.
Please note proper CAN protocol must be followed. See manual below for guidance.
SKU 101-0116
This sensor can be used with all wide band controllers and ECU’s that support LSU 4.9 sensors. This includes:
Link G4+/G4X Fury and G4+Thunder ECU’s – These have on-board LSU4.9 wide-band control.
Link CAN-Lambda Controller – These are sold new with a sensor, so this sensor by itself is only required if you need a replacement.
Specifications:
Application: lambda 0.65 to ∞
Exhaust gas temperature: 930°C (1,030 for a short time)
Hexagon temperature: 600°C
Thread: M18x1.5
Weight: 120 g
Includes plug and pin kit
SKU 101-0117
Used to install LSU 4.9 Wideband O2 sensor. Includes weld on bung and plug.
O2 Bung and Plug
SKU 101-0127
LSU 4.9 Plug Kit
SKU 101-0106
Want to add additional inputs/output to your Link Plugin ECU? Use the XS Loom. The Link XS Loom plugs into the expansion connector on all Link G4, G4+ and G4X plug-in ECUs. The number of extra inputs and outputs added by the XS Loom is dependent on the Plugin ECU. For specific details check the plug-in ECUs specifications.
Common applications include but are not limited to:
Boost adjustment knob or switch
Wide-band AFR/Lambda
Oil Pressure Sensor
Fuel Pressure Sensor
Inlet Air Temperature (IAT) sensor
Map switch (Different tunes available via toggle switch)
The XS Loom is 2.5m long and uses 20AWG wire.
SKU 101-0015
More boost? Of course and this 3 port boost control solenoid will help you do it.
3 port boost control solenoids are the go-to for the majority of boost control applications, they allow for precise control of boost and boost levels can be raised to around 2-3 times the spring pressure of the wastegate.
For higher boost applications consider our 4-Port boost control solenoid.
Features:
Compatible with all Link ECU’s
Can be used with single or multiple wastegates (Using T junction)
Compatible with internal or external wastegates
Fast and consistent response times
High shifting forces
MAC 35 series – Rugged, reliable and long operational life
Short stroke, high flow
Balanced poppet, immune to variations of pressure
We recommend starting with a PWM Frequency of 20Hz for this Boost control solenoid. A detailed description of setting up boost control can be found in the help file in our PCLink software which is available for free download.
Specifications:
MAC 35 series
120 PSI max
1/8” BSPPL
12 VDC (5.4W)
18” (45cm) coil leads
Includes 3 x 1/8” BSP hose tail fittings for easy connection
SKU 101-0016
Thinking of turning up the boost to max? Then this 4 port boost control solenoid is perfect. It allows for precise boost control of up to 120PSI.
4 port Boost control solenoids are commonly used for big boost applications, boost levels can be raised as high as 6-7 times the spring pressure of the wastegate and they allow you to use lower wastegate spring pressures for more precise boost control when launching. Particularly useful in high power traction limited situations where you might want low boost in low gears and higher boost in high gears.
Features:
Up to 120PSI
Compatible with all Link ECU’s
Can be used with single or multiple wastegates
Fast and consistent response times
High shifting forces
MAC 45 series – Rugged, reliable and long operational life
Short stroke, high flow
Balanced poppet, immune to variations of pressure
We recommend starting with a PWM Frequency of 25Hz for this Boost control solenoid. A detailed description of setting up boost control can be found in the help file within the PCLink software which is available for free download.
Specifications:
MAC 45 series
120 PSI max
1/8” BSPPL
12 VDC (5.4W) 18” (45cm) coil leads
Includes 4 x 1/8” BSP hose tail fittings for easy connection
SKU 101-0045
Includes 2-pin Deutsch DTM connector kit
Aluminium and steel weld in mounting bosses available
1/8" NPT Thread
SKU 101-0048
Includes Plug Kit - 2 way Bosch Style plug, terminals and boot
Aluminium and steel weld in mounting bosses available (IATBMA & IATBMS)
SKU 101-0076
Includes 2-pin Deutsch DTM connector kit
Aluminium and steel weld in mounting bosses available
1/8" NPT Thread
SKU 101-0077
Includes Plug Kit - 2 way Bosch Style plug, terminals and boot
M12 Thread
SKU 101-0320
Two sensors in one - Combined 10 bar (145 psi) Liquid Pressure sensor and -40 to 140 deg C L Liquid Temperature sensor.
Suitable for Diesel, gasoline, E85, engine oil, transmission oil
Up to 10.0 bar (145PSI/1000kpa) Pressure Sensor for Liquid
-40 to 140°C (-40 to 284°F) Temperature sensor for Liquid
45degree cone seat, M10x1 fitting
Includes Bosch Trapez 4-pin mating connector kit
Not suitable for water/coolant.
Technical Specs:
See attached image.
SKU 101-0199
Stainless Steel thread adapter, M10 x 1 Female to 1/8 BSP Male, Adapts popular Bosch Metric Pressure Sensors to suit 1/8 BSP threaded ports.
SKU 101-0193
Stainless Steel thread adapter, M10 x 1 Female to 1/8 NPT Male, Adapts popular Bosch Metric Pressure Sensors to suit 1/8 NPT threaded ports.
SKU 101-0049
Weld in Aluminium Boss. Bosch part. Suitable for mounting the IATB Inlet Air Temperature sensor and other sensors that mount via a Bosch style flange.
SKU 101-0050
Weld in Steel Boss. Bosch part. Suitable for mounting the IATB Inlet Air Temperature sensor and other sensors that mount via a Bosch style flange.
SKU 101-0046
Weld in Aluminium boss, 1/8" NPT Thread. Suitable for mounting Intake air temperature (IAT1-8), Coolant Temperature sensors (NTC1-8) and other sensors that use 1/8" NPT Thread.
SKU 101-0047
Weld in steel boss, 1/8" NPT Thread. Suitable for mounting Intake air temperature (IAT1-8), Coolant Temperature sensors (NTC1-8) and other sensors that use 1/8" NPT Thread.
SKU 101-0325
Media Isolated 150PSI/10 Bar Pressure Sensor, 1/8 NPT
The MIPS 150PSI/10 Bar Pressure Sensor features a durable stainless steel construction and is designed for compatibility with various fluids, including oil, petrol, and water.
Features:
• Quality Honeywell sensor, Rugged Stainless Steel Construction
• 1/8 NPT, 22mm hex
• Includes connector kit (3-Way Metri-Pack 150)
• Rated from -40ºC to 125ºC
• 5V Supply (4.75V to 5.25V)
• 0.5V to 4.5V Output voltage
• Suitable for use with oil, petrol, ethanol, diesel, coolant, water.r compatibility with various fluids, including oil, petrol, and water.
SKU 101-0320
Two sensors in one - Combined 10 bar (145 psi) Liquid Pressure sensor and -40 to 140 deg C L Liquid Temperature sensor.
Suitable for Diesel, gasoline, E85, engine oil, transmission oil
Up to 10.0 bar (145PSI/1000kpa) Pressure Sensor for Liquid
-40 to 140°C (-40 to 284°F) Temperature sensor for Liquid
45degree cone seat, M10x1 fitting
Includes Bosch Trapez 4-pin mating connector kit
Not suitable for water/coolant.
For full image technical specs click the link below
SKU 101-0080
Oil or Fuel pressure
10 Bar/150psi
1/8” NPT Thread
Includes plug and pin kit
Technical Specs and Wiring
Up to 150 PSI above atmospheric pressure, cannot be used to read vacuum
0.5v = 0bar / 0PsiG
4.5v = 10 Bar / 145.03PsiG
SKU 101-0186
High Pressure sensor for Liquid. Use for Fuel, Clutch, Brake etc.
140 Bar/2030PSI
45degree cone seat
M10x1 Thread
Includes mating connector kit
Technical Specs:
Up to 2030 PSI above atmospheric pressure, cannot be used to read vacuum
See attached image for more.
SKU 101-0326
Oil or Fuel pressure
10 Bar/150psi
1/8” NPT Thread
Includes plug and pin kit
Technical Specs and Wiring
Up to 150 PSI above atmospheric pressure, cannot be used to read vacuum
0.5v = 0bar / 0PsiG
4.5v = 10 Bar / 145.03PsiG
This listing is for a sensor with updated enclosure, as of May 2025.
SKU 101-0199
Stainless Steel thread adapter, M10 x 1 Female to 1/8 BSP Male, Adapts popular Bosch Metric Pressure Sensors to suit 1/8 BSP threaded ports.
SKU 101-0193
Stainless Steel thread adapter, M10 x 1 Female to 1/8 NPT Male, Adapts popular Bosch Metric Pressure Sensors to suit 1/8 NPT threaded ports.
SKU 101-0298
The 8 Bar MAP Variohm Eurosensor reads up to 7 Bar absolute pressure.
This means that it is suitable for turbo or supercharged applications running up to 7 Bar (or 101psi) of boost pressure.
Includes Plug and Pins
Push wire through connector; crimp on terminal; pull wire/terminal back into connector
Using Link G4/G4+/G4X ECU’s select the MAP sensor type in PC Link as ‘Variohm 8 Bar’
Calibration - 0kpa = 0.5v, 800kpa = 4.5v
PIN A = 0v
PIN B = 5v
PIN C = Signal
SKU 101-0295
The 5 Bar MAP Variohm Eurosensor reads up to 4 Bar absolute pressure.
This means that it is suitable for turbo or supercharged applications running up to 4 Bar (or 58psi) of boost pressure.
Includes Plug and Pins
Push wire through connector; crimp on terminal; pull wire/terminal back into connector
Using Link G4/G4+/G4X ECU’s select the MAP sensor type in PC Link as ‘Variohm 5 Bar’
Calibration - 0kpa = 0.5v, 500kpa = 4.5v
PIN A = 0v
PIN B = 5v
PIN C = Signal
SKU 101-0165
The Link 4 Bar MAP sensor reads up to 4 Bar absolute pressure. This means that it is suitable for turbo or supercharged applications running up to 3.0 Bar (or 44psi) of boost pressure. The wiring pinout for this sensor is marked directly on the sensor.
Includes 3-pin Deutsch DTM connector kit
Easy to mount via 2 bolt holes. Note that the sensor should be mounted higher than the intake manifold port that the hose connects to.
Compact aluminium enclosure
Mechanical connection via 4mm (3/16″) hose connector nipple.
Using Link G4/G4+/G4X ECU’s just select the MAP sensor type in PC Link as ‘Link 4 Bar’
SKU 101-0164
This Link MAP sensor reads up to 3 Bar absolute pressure. This means that it is suitable for turbo or supercharged applications running up to 2.0 Bar (or 29psi) of boost pressure. The wiring pinout for this sensor is indicated on the sensor.
Includes Deutsch 3-pin connector kit
Easy to mount via 2 bolt holes. Note that the sensor should be mounted higher than the intake manifold port that the hose connects to.
Compact aluminium enclosure
Mechanical connection via 4mm hose connector nipple
Using Link G4/G4+/G4X ECU’s select the MAP sensor type in PC Link as ‘Link 3 Bar’
SKU 101-0163
Link 2.5 Bar MAP sensor reads up to 2.5 Bar absolute pressure. This means that it is suitable for turbo or supercharged applications running up to 1.5 Bar (approx 22psi) of boost pressure. The wiring pinout for this sensor is marked directly on the sensor.
Includes 3-pin Deutsch DTM connector kit
Easy to mount via 2 bolt holes. Note that the sensor should be mounted higher than the intake manifold port that the hose connects to.
Compact aluminium enclosure
Mechanical connection via 4mm (3/16″) hose connector nipple.
Using Link G4/G4+/G4X ECU’s select the MAP sensor type in PC Link as ‘Link 2.5 Bar’
SKU 101-0162
The Link 1.15 Bar MAP sensor reads up to 1.15 Bar absolute pressure. This means it is suitable for use in naturally aspirated engines. This MAP sensor can also be used in applications where positive intake pressures of up to 0.15 Bar (approx 2 PSI) are expected (eg. Ram-air effect). The wiring pinout for this sensor is marked directly on the housing.
Includes 3-pin Deutsch DTM connector kit
Easy to mount via 2 bolt holes. Note that the sensor should be mounted higher than the intake manifold port that the hose connects to.
Compact aluminium enclosure
Very high resolution readings for naturally aspirated engines
Mechanical connection via 4mm (3/16″) hose connector nipple.
Using Link G4/G4+/G4X ECU’s select the MAP sensor type in PC Link as ‘Link 1.15 Bar’
No results found
No results match your search. Try removing a few filters.
Special Order Parts
Parts Available but will need sales representative assistance.
Special shipping/part fitment
Click HERE or on any image to request a quote for any part you do not see on the website.
We will be adding more parts to the website daily so check back for new inventory.