Discount applied at checkout
Universal Parts
Universal Parts
Filters
PUMP FEATURES:
• Flows 340LPH @ 3bar, 13.5v (90GPH @ 45psi)
• Internal Check Valve •Maximum Pressure - 5.9 Bar (85psi)
•Can be used in carbureted and EFI applications
•Each pump is individually tested for performance and includes flow and current draw report
•Designed for in-tank use only
•Sending Unit not included
•Comes with rubber sleeve, end cap, pre-filter, hose, clamps and wire leads.
Horsepower: 475 - 825 Displacement: 2.0L - 3.5L
New compressor aero technology increases power and performance.
• Direct upgrade path for Gen I customers with just a CHRA purchase.
• G-Series II utilizes Gen I compressor and turbine housings.
• Up to 10% higher compressor flow compared to G-Series Gen I at peak pressure ratio and peak turbo RPM.
• Calibration required to take advantage of increased flow for a horsepower upgrade.
• Increased efficiency at high flow rates.
• Standard and reverse rotation configurations in Supercore, CHRA, and Turbo models.
• Mar-M alloy turbine wheel rated up to 1050° C.
• Stainless steel turbine housings are rated up to 1050° C.
• Oil restrictor and water fittings included.
G-Series II is a direct upgrade path for Gen I customers with just a CHRA purchase because the compressor housings have the same contour. This allows existing Gen I customers to use their compressor cover when upgrading.
A one-piece center housing and backplate increase durability and product safety by reducing the number of failure points associated with the turbocharger. The center housing to turbine housing V-Band connection allows for 360 degree orientation when installing with Garrett non-wastegated turbine housings.
Horsepower: 550 - 990 Displacement: 2.0L - 5.5L
• New compressor aero technology increases power and performance.
• Direct upgrade path for Gen I customers with just a CHRA purchase. (see options below)
• G-Series II utilizes Gen I compressor and turbine housings.
• Up to 10% higher compressor flow compared to G-Series Gen I at peak pressure ratio and peak turbo RPM.
• Calibration required to take advantage of increased flow for a horsepower upgrade.
• Increased efficiency at high flow rates.
• Standard and reverse rotation configurations in Supercore, CHRA, and Turbo models.
• Mar-M alloy turbine wheel rated up to 1050° C.
• Stainless steel turbine housings are rated up to 1050° C.
• Oil restrictor and water fittings included.
Compressor
Inducer: 62mm; Exducer: 76mm; Trim: 65; A/R: .72
Turbine
Inducer: 68mm; Exducer: 62mm; Trim: 68
Horsepower: 350-700 Displacement: 1.4L - 3.0L
• New compressor aero technology increases power and performance.
• Direct upgrade path for Gen I customers with just a CHRA purchase.
• G-Series II utilizes Gen I compressor and turbine housings.
• Up to 10% higher compressor flow compared to G-Series Gen I at peak pressure ratio and peak turbo RPM.
• Calibration required to take advantage of increased flow for a horsepower upgrade.
• Increased efficiency at high flow rates.
• Standard and reverse rotation configurations in Supercore, CHRA, and Turbo models.
• Mar-M alloy turbine wheel rated up to 1050° C.
• Stainless steel turbine housings are rated up to 1050° C.
• Oil restrictor and water fittings included.
Horsepower: 350-725 Displacement: 2L - 3.5L
New compressor aero technology increases power and performance.
• Direct upgrade path for Gen I customers with just a CHRA purchase.
• G-Series II utilizes Gen I compressor and turbine housings.
• Up to 10% higher compressor flow compared to G-Series Gen I at peak pressure ratio and peak turbo RPM.
• Calibration required to take advantage of increased flow for a horsepower upgrade.
• Increased efficiency at high flow rates.
• Standard and reverse rotation configurations in Supercore, CHRA, and Turbo models.
• Mar-M alloy turbine wheel rated up to 1050° C.
• Stainless steel turbine housings are rated up to 1050° C.
• Oil restrictor and water fittings included.
Horsepower: 300 - 585 Displacement: 1.4L - 3.0L
G-SERIES II UNIVERSAL PERFORMANCE TURBOCHARGER
G25-585 | 49mm Turbine
New compressor aero increases power and performance.
Up to 10% higher compressor flow compared to G-Series Gen I at peak pressure ratio and peak turbo RPM.
Direct upgrade path for Gen I customers with just a CHRA swap.
Utilizes Gen I compressor and turbine housings.
Standard and reverse rotation configurations.
Turbine wheel constructed of Mar-M alloy rated up to 1050°C.
Oil restrictor and water fittings included.
Competitor Frame Size Reference: 4849 (48mm compressor inducer / 49mm turbine exducer)
Horsepower: 550 - 900 Displacement: 2.0L - 3.5L
G SERIES COMPRESSOR AERODYNAMICS FOR MAXIMUM HP
62mm TURBOCHARGER COMPRESSOR WHEEL
77% MAXIMUM COMPRESSOR EFFICIENCY
MAR-M ALLOY TURBINE WHEEL RATED UP TO 1050° C
NEW TURBINE AERO PROVIDES HIGHER FLOW AND EFFICIENCY
STAINLESS STEEL TURBINE HOUSINGS RATED UP TO 1050° C
OIL RESTRICTOR AND WATER FITTINGS INCLUDED
FULLY MACHINED SPEED SENSOR AND PRESSURE PORTS
Compressor Inducer 62mm, Exducer 76mm, Trim 65, A/R 0.72
Turbine Inducer 60mm, Exducer 55mm, Trim 84
SPEED SENSOR The compressor housing features a fully machined ported shroud to help reduce compressor surge. A fully machined speed sensor port provides enthusiasts the option to add the new G Series speed sensor to measure turbocharger shaft speed, a key factor in determining ideal operating conditions.
The new speed sensor is easy to install and does not need to be adjusted for length like previous sensors. Simply remove and plug, then insert the speed sensor and tighten the bolt. The new speed sensor is sold separately and is not compatible with GT and GTX sensors due to the new design and sizing.
The addition of an o-ring between the compressor housing and backplate reduces the possibility of boost pressure leakage.
*G Series speed sensor kits have new part numbers and are not compatible with GT/GTX kits. sold separately
The compressor housing features a fully machined ported shroud to help reduce compressor surge. A fully machined speed sensor port provides enthusiasts the option to add the new G Series speed sensor to measure turbocharger shaft speed, a key factor in determining ideal operating conditions.
The new speed sensor is easy to install and does not need to be adjusted for length like previous sensors. Simply remove and plug, then insert the speed sensor and tighten the bolt. The new speed sensor is sold separately and is not compatible with GT and GTX sensors due to the new design and sizing.
The addition of an o-ring between the compressor housing and backplate reduces the possibility of boost pressure leakage.
*G Series speed sensor kits have new part numbers and are not compatible with GT/GTX kits.
Part numbers (choose accordingly)
G Series \ GTX55 Gen II \ GTX50 Gen II \ GTX47 Gen II -
781328-0003 (Street) 781328-0004 (Pro)
(Older models) GTX Gen II \ GTX \ GT \ GTW -
781328-0001 (Street) 781328-0002 (Pro)
The most powerful small frame turbocharger series on the market
Horsepower: 475-770 Displacement: 2.0L - 3.5L
G SERIES COMPRESSOR AERODYNAMICS FOR MAXIMUM HP
58mm TURBOCHARGER COMPRESSOR WHEEL
76% MAXIMUM COMPRESSOR EFFICIENCY
MAR-M ALLOY TURBINE WHEEL RATED UP TO 1050° C
NEW TURBINE AERO PROVIDES HIGHER FLOW AND EFFICIENCY
STAINLESS STEEL TURBINE HOUSINGS RATED UP TO 1050° C
OIL RESTRICTOR AND WATER FITTINGS INCLUDED
FULLY MACHINED SPEED SENSOR AND PRESSURE PORTS
Read About Turbo System Optimization: A guide to setting up your turbocharger
Compressor Inducer 58mm, Exducer 71mm, Trim 65, A/R 0.72
Turbine Inducer 60mm, Exducer 55mm, Trim 84
SPEED SENSOR The compressor housing features a fully machined ported shroud to help reduce compressor surge. A fully machined speed sensor port provides enthusiasts the option to add the new G Series speed sensor to measure turbocharger shaft speed, a key factor in determining ideal operating conditions.
The new speed sensor is easy to install and does not need to be adjusted for length like previous sensors. Simply remove and plug, then insert the speed sensor and tighten the bolt. The new speed sensor is sold separately and is not compatible with GT and GTX sensors due to the new design and sizing.
The addition of an o-ring between the compressor housing and backplate reduces the possibility of boost pressure leakage.
*G Series speed sensor kits have new part numbers and are not compatible with GT/GTX kits. sold separately
G-XRace Turbine Housing Kits
G-XRace GXR40 turbine housing kits are available in four A/R. 0.85 A/R | 0.95 A/R | 1.06 | 1.19 A/R stainless steel housings with T4 divided or V-Band turbine inlet flanges. G-XRace utilizes the same twin-scroll T4 and V-Band turbine housings as G-Series to enable an easy upgrade.
Horsepower: 500 - 1150
Displacement: 2.0L - 6.0L
Product Line G-XRace
Frame Size 40
Rotation Standard
Cooling Oil & Water Cooled
Bearing Ceramic Dual Ball Bearing
Compressor Wheel Specs
Compressor Exducer (mm) 88
Compressor Wheel Mat Forged Fully Machined
Compressor A/R 0.85
Turbine Wheel Specs
Turbine Inducer (mm) 77
Turbine Exducer (mm) 70
Turbine Trim 84
Turbine Wheel Mat Inconel
G-XRace GXR55-88 0.25″ Map Groove 103MM Turbine
G-XRace GXR55 turbine housing kits are available in two A/R. 1.24 A/R | 1.40 A/R stainless steel housings with V-Band turbine inlet flanges. G-XRace utilizes the same V-Band turbine housings as G-Series to enable an easy upgrade.
For drag racing classes - LDR, X275
Horsepower: 1000 - 2350
Displacement: 3.0L - 12.0L
Product Line: G-XRace
Frame Size: 55
Rotation: Standard
Cooling: Oil Cooled
Bearing: Ceramic Dual Ball Bearing
Compressor Wheel Specs
Compressor Exducer (mm): 133
Compressor Wheel Mat: Forged Fully Machined
Compressor A/R: .88
Turbine Wheel Specs
Turbine Inducer (mm): 112
Turbine Exducer (mm): 103
Turbine Trim: 86
Turbine Wheel Mat: Inconel
Engine Characteristics
Min HP: 1000
Max HP: 2350
Min Displacement (L): 3.0
Max Displacement (L): 12.0
GARRETT GXR55-88 .18" Map Groove 106MM Turbine Wheel
Horsepower: 1000 - 2350 Displacement: 3.0L - 12.0L
G-XRace Turbine Housing Kits
G-XRace GXR55 turbine housing kits are available in multiple A/R. 1.24 A/R | 1.40 A/R stainless steel housings with V-Band turbine inlet flanges and 1.00 A/R | 1.12 A/R | 1.24 A/R | 1.40 A/R with T6 turbine inlet flanges. G-XRace utilizes the same V-Band turbine housings as G-Series to enable an easy upgrade.
Product Line: G-XRace
Frame Size: 55
Rotation: Standard
Cooling: Oil Cooled
Bearing: Ceramic Dual Ball Bearing
Compressor Wheel Specs
Compressor Exducer (mm): 133
Compressor Wheel Mat: Forged Fully Machined
Compressor A/R: .88
Turbine Wheel Specs
Turbine Inducer (mm): 112
Turbine Exducer (mm): 106
Turbine Trim: 90
Turbine Wheel Mat: Inconel
Engine Characteristics
Min HP: 1000
Max HP: 2350
Min Displacement (L): 3.0
Max Displacement (L): 12.0
G-XRace GXR55-88 0.18″ Map Groove 103MM Turbine
G-XRace GXR55 turbine housing kits are available in two A/R. 1.24 A/R | 1.40 A/R stainless steel housings with V-Band turbine inlet flanges. G-XRace utilizes the same V-Band turbine housings as G-Series to enable an easy upgrade.
For drag racing class - X275
Horsepower: 1000 - 2350
Displacement: 3.0L - 12.0L
Product Line: G-XRace
Frame Size: 55
Rotation: Standard
Cooling: Oil Cooled
Bearing: Ceramic Dual Ball Bearing
Compressor Wheel Specs
Compressor Exducer (mm): 133
Compressor Wheel Mat: Forged Fully Machined
Compressor A/R: .88
Turbine Wheel Specs
Turbine Inducer (mm): 112
Turbine Exducer (mm): 103
Turbine Trim: 86
Turbine Wheel Mat: Inconel
Engine Characteristics
Min HP: 1000
Max HP: 2350
Min Displacement (L): 3.0
Max Displacement (L): 12.0
GARRETT GXR55-88 .25" Map Groove 106MM Turbine Wheel
For Drag racing classes: LDR, X275 - 0.25″ Map Groove
Horsepower: 1000 - 2350
Displacement: 3.0L - 12.0L
G-XRace Turbine Housing Kits
G-XRace GXR55 turbine housing kits are available in multiple A/R. 1.24 A/R | 1.40 A/R stainless steel housings with V-Band turbine inlet flanges and 1.00 A/R | 1.12 A/R | 1.24 A/R | 1.40 A/R with T6 turbine inlet flanges. G-XRace utilizes the same V-Band turbine housings as G-Series to enable an easy upgrade.
Product Line: G-XRace
Frame Size: 55
Rotation: Standard
Cooling: Oil Cooled
Bearing: Ceramic Dual Ball Bearing
Compressor Wheel Specs
Compressor Exducer (mm): 133
Compressor Wheel Mat: Forged Fully Machined
Compressor A/R: .88
Turbine Wheel Specs
Turbine Inducer (mm): 112
Turbine Exducer (mm): 106
Turbine Trim: 90
Turbine Wheel Mat: Inconel
Engine Characteristics
Min HP: 1000
Max HP: 2350
Min Displacement (L): 3.0
Max Displacement (L): 12.0
GARRETT GXR45-67
Horsepower: 725 - 1475 Displacement: 2.0L - 8.0L
Product Line: G-XRace
*Optional Compressor Housing -For classes with 0.25″ map groove rule (PanAm, etc)
Frame Size: 45
Rotation: Standard
Cooling: Oil & Water Cooled
Wastegate: External
Inlet: V-band or T4
Outlet: V-band
Bearing: Ceramic Dual Ball Bearing
Compressor Wheel Specs
Compressor Exducer (mm): 102
Compressor Wheel Mat: Forged Fully Machined
Compressor A/R: .85
Turbine Wheel Specs
Turbine Inducer (mm): 89
Turbine Exducer (mm): 82
Turbine Trim: 84
Turbine Wheel Mat: Inconel
Engine Characteristics
Min HP: 725
Max HP: 1475
Min Displacement (L): 2.0
Max Displacement (L): 8.0
GARRETT GXR42-72
Horsepower: 700-1450 Displacement: 2.0L - 7.0L
Product Line: G-XRace
Frame Size: 42
Rotation: Standard
Cooling: Oil & Water Cooled
Wastegate: External
Bearing: Ceramic Dual Ball Bearing
Compressor Wheel Specs
Compressor Exducer (mm): 102
Compressor Wheel Mat: Forged Fully Machined
Compressor A/R: 51
Turbine Wheel Specs
Turbine Inducer (mm): 82
Turbine Exducer (mm): 75
Turbine Trim: 84
Turbine Wheel Mat: Inconel
Engine Characteristics
Min HP: 700
Max HP: 1450
Min Displacement (L): 2.0
Max Displacement (L): 7.0
Run the WCF Winning GARRETT GXR45-73
Horsepower: 750 - 1550 Displacement: 2.0L - 8.0L
Product Line: G-XRace
*Optional Compressor Housing -For classes with 0.25″ map groove rule (PanAm, etc)
Frame Size: 45
Rotation: Standard
Cooling: Oil & Water Cooled
Wastegate: External
Inlet: V-band or T4
Outlet: V-band
Bearing: Ceramic Dual Ball Bearing
Compressor Wheel Specs
Compressor Exducer (mm): 102
Compressor Wheel Mat: Forged Fully Machined
Compressor A/R: .85
Turbine Wheel Specs
Turbine Inducer (mm): 89
Turbine Exducer (mm): 82
Turbine Trim: 84
Turbine Wheel Mat: Inconel
GARRETT GXR42-68
Horsepower: 650 - 1400 Displacement: 2.0L - 7.0L
Product Line: G-XRace
Frame Size: 42
Rotation: Standard
Cooling: Oil & Water Cooled
Wastegate: External
Bearing: Ceramic Dual Ball Bearing
Compressor Wheel Specs
Compressor Exducer (mm): 68
Compressor Wheel Mat: Forged Fully Machined
Compressor A/R: .85
Turbine Wheel Specs
Turbine Inducer (mm): 82
Turbine Exducer (mm): 75
Turbine Trim: 84
Turbine Wheel Mat: Inconel
Engine Characteristics
Min HP: 650
Max HP: 1400
Min Displacement (L): 2.0
Max Displacement (L): 7.0
HP: 700-1050 Disp: 2.0L-5.5L
Product Line: G-Series
Frame Size : 35
Rotation: Standard
Cooling: Oil & Water Cooled
Wastegate: External
Bearing: Ceramic Dual Ball Bearing
Turbine Wheel Specs
Turbine Inducer (mm): 68
Turbine Exducer (mm): 62
Turbine Trim: 84
Compressor Wheel Specs
Compressor Exducer (mm): 84
Compressor Wheel Mat: Forged Fully Machined
Compressor A/R: 0.75
Horsepower: 550 - 900 Displacement: 2.0L - 5.5L
Product Line: G-Series
Frame Size: 35
Rotation: Standard and Reverse
Cooling: Oil & Water Cooled
Wastegate: External or Internal
Bearing: Ceramic Dual Ball Bearing
Turbine Wheel Specs
Turbine Inducer (mm): 68
Turbine Exducer (mm): 62
Turbine Trim :84
Turbine Wheel Mat: Mar-M
Compressor Wheel Specs
Compressor Exducer (mm): 76
Compressor Wheel Mat: Forged Fully Machined
Compressor A/R: 0.72
Universal Installation Kit
Fits Hellcat 535lph and 450lph pumps
Kit includes : Fuel Filter/Wiring Harness/Fuel Line for E85 Pumps/hardware-clamps
Universal Fuel Pump
Description: E85 Fuel Pump
Mounting Hardware Included:NO
Fuel Type:FLEX
Diameter: 0.34375
Inlet Type: TURBINE INLET
Outlet Type: DUAL BARBED
Operating Pressure: 40
Flow Rate: 115 GAL. @ 40 PSI
Maximum Working Pressure: 110
Amperage Rating: 15.5 @ 40 PSI
Strainer Included: NO
Universal 535lph In-Tank Fuel 39/80 Flex Fuel
Available with or without check valve - without check valve offers slightly more flow
Inlet Type: TURBINE INLET
Outlet Type: DUAL BARBED
Operating Pressure: 40
Flow Rate: 125 GAL. @ 40 PSI
Maximum Working Pressure: 125
Amperage Rating: 19.0 @ 40 PSI
Strainer Included: NO
Mounting Hardware Included: NO
Diameter: 0.4375
SKU 101-0034
Looking to run flex-fuel? Then the Ethanol Content Sensor is a must have. The Ethanol Content Sensor measures the ratio of ethanol to petrol in a flex fuel vehicle. This sensor also measures fuel temperature. Compatible with all current Link Wire-In and Plug-In ECU’s. Uses 1 Digital input on the ECU. The sensor is fitted to the vehicle’s fuel return line anywhere between the fuel pressure regulator and the fuel tank.
AN-6 Fittings
Includes plug and pin kit
Technical Specs
The pinout is indicated on the sensor itself (from left to right looking into connector on sensor) as :
1.) Vcc (+12V supply)
2.) GND (ground)
3.) Vout (digital signal out)
Vibrant Crankcase Breather Filter w/Chrome Cap
Vibrant's Breather Filters feature a premium 4-Ply cotton-gauze filter elements that provide significantly more airflow than a stock filter while providing excellent filtration.
Perfect for Crankcases or Catch Cans that Require Small Filters * Available in Many Sizes and Shapes
Air filter for 3/4" connections. Hose clamp included.
AEM DryFlow Air Filter
Air Filter Color: Red
Air Filter Large End Diameter: 6 in (152 mm)
Air Filter Material: Non-woven Synthetic
Air Filter Shape: Tapered Conical
Base Outside Diameter: 6 in (152 mm)
Filter Material: Non-woven Synthetic
Flange Angle: 0 degrees
Flange Inside Diameter: 3 in (76 mm)
Flange Length: 1.5 in (38 mm)
Flange Offset: 0 in (0 mm)
Flange Type: Centered
Flanges: 1
Height: 5.125 in (130 mm)
Shape: Tapered Conical
Top Outside Diameter: 5.125 in. (130mm)
Washable: Yes
AEM DryFlow Air Filter
Air Filter Color: Red
Air Filter Large End Diameter: 6 in (152 mm)
Air Filter Material: Non-woven Synthetic
Air Filter Shape: Tapered Conical
Base Outside Diameter: 6 in (152 mm)
Filter Material: Non-woven Synthetic
Flange Angle: 0 degrees
Flange Inside Diameter: 3.5 in (89 mm)
Flange Length: 1.375 in (35 mm)
Flange Offset: 0 in (0 mm)
Flange Type: Centered
Flanges: 1
Height: 5.25 in (133 mm)
Shape: Tapered Conical
Top Outside Diameter: 5.125 in. (130mm)
Washable: Yes
Base Outside Diameter: 6.000 in. (152mm)
AEM DryFlow Air Filter
Air Filter Color: Red
Air Filter Large End Diameter: 6 in (152 mm)
Air Filter Material: Non-woven Synthetic
Air Filter Shape: Tapered Conical
Base Outside Diameter: 6 in (152 mm)
Filter Material: Non-woven Synthetic
Flange Angle: 0 degrees
Flange Inside Diameter: 4 in (102 mm)
Flange Length: 1.5 in (38 mm)
Flange Offset: 0 in (0 mm)
Flange Type: Centered
Flanges: 1
Height: 5.25 in (133 mm)
Top Outside Diameter: 5.125 in (130 mm)
Top Style: Rubber
Air Filter Large End Diameter: 6.000 in. (152mm)
Machine Washable: Yes
Base Outside Diameter: 6.000 in. (152mm)
AEM DryFlow Air Filter
Air Filter Color: Red
Air Filter Large End Diameter: 5.75 in (146 mm)
Air Filter Material: Non-woven Synthetic
Air Filter Shape: Tapered Conical
Base Outside Diameter: 5.75 in (146 mm)
Filter Material: Non-woven Synthetic
Flange Angle: 0 degrees
Flange Inside Diameter: 4 in (102 mm)
Flange Length: 0.938 in (24 mm)
Flange Offset: 0 in (0 mm)
Flange Type: Centered
Flanges: 1
Height: 7 in (178 mm)
Top Outside Diameter: 4.75 in (121 mm)
Top Style: Rubber
Washable: Yes
AEM DryFlow Air Filter
Air Filter Color: Red
Air Filter Large End Diameter: 6 in (152 mm)
Air Filter Material: Non-woven Synthetic
Air Filter Shape: Tapered Conical
Base Outside Diameter: 6 in (152 mm)
Filter Material: Non-woven Synthetic
Flange Angle: 0 degrees
Flange Inside Diameter: 4 in (102 mm)
Flange Length: 1.438 in (37 mm)
Flange Offset: 0 in (0 mm)
Flange Type: Centered
Flanges: 1
Height: 9.188 in (233 mm)
Top Outside Diameter: 5.125 in (130 mm)
Top Style: Rubber
No results found
No results match your search. Try removing a few filters.
Special Order Parts
Parts Available but will need sales representative assistance.
Special shipping/part fitment
Click HERE or on any image to request a quote for any part you do not see on the website.
We will be adding more parts to the website daily so check back for new inventory.