Discount applied at checkout
Wire in ECU's
Wire in ECU's
Filters
153-9300B
Alongside the G5 Voodoo Pro, the bundle includes 2.5 m A and B looms, an E connector plug and pin kit, two Bosch LSU 4.9 wideband Lambda sensors, a Link 4 bar MAP sensor and an intake air temperature (IAT) sensor with a 1/8" NPT thread.
With dual onboard Digital Wideband Lambda Control, both LSU 4.9 sensors wire straight into the ECU, giving you fast and accurate live Lambda from both sensors with no external controllers needed. The MAP and IAT sensors each come with their Deutsch DTM connector kit, and the LSU 4.9 sensors come with their plug and pin kits. The 4 bar MAP sensor suits turbo or supercharged engines running up to 3.0 bar (44 psi) of boost.
Advanced communications include GPS, Wi-Fi, Ethernet, dual CAN Bus and USB-C tuning, alongside 1GB of onboard data logging for high-speed data capture and analysis. The G5 Voodoo Pro also features automatic transmission control and dual H-bridges for E-Throttle and low power E-Wastegate control.
The G5 Voodoo Pro is the ideal solution for modern high-performance street and motorsport builds requiring maximum I/O, dual Lambda control and the full capability of Link next-generation of engine management technology.
Models Supported
The G5 Voodoo Pro can run: 12 cylinders sequential port or direct injection and direct spark, or 8 cylinders with direct/port staged injection, and direct spark.
111-9300B
Alongside the AtomX, the bundle includes a 2.5 m A loom, a CAN Lambda wideband controller with a Bosch LSU 4.9 sensor, a Link 1.15 bar MAP sensor and an intake air temperature (IAT) sensor with a 1/8" NPT thread.
The CAN Lambda is essential for modern tuning, giving you fast and accurate live Lambda without using up any DI or An Volt inputs. Each sensor comes with its Deutsch DTM connector kit, and the 1.15 bar MAP sensor gives high resolution readings on naturally aspirated engines.
As Link entry-level ECU, the AtomX delivers proven performance in a compact and capable package with exceptional value.
127-9300B
Alongside the MonsoonX, the bundle includes a 2.5 m A loom, a CAN Lambda wideband controller with a Bosch LSU 4.9 sensor and an intake air temperature (IAT) sensor with a 1/8" NPT thread.
The CAN Lambda is essential for modern tuning, giving you fast and accurate live Lambda without using up any DI or An Volt inputs. Each sensor comes with its Deutsch DTM connector kit, and the MonsoonX built-in MAP sensor completes the core sensor set.
Bridging the gap between the entry and mid-level ECUs, the MonsoonX delivers advanced tuning and motorsport features in a compact and capable package.
The MonsoonX is the ideal solution for naturally aspirated and turbocharged engines that require some of the advanced tuning and motorsport features, without needing to step up to one of Link higher-level ECUs.
Models Supported
The MonsoonX can control up to 2 rotors or 4 cylinders with sequential injection and direct spark.
127-9800B
G4X Monsoon Wire-In Bundle. Everything you need to get started wiring a Link G4X MonsoonX ECU into your chosen vehicle.Â
This package is ideal for four cylinder engines requiring a few additional features.
Medium A Loom - 2.5m length A loom for G4X ECUs (MonsoonX)
Air temperature sensor
Coolant temperature sensor
Pressure sensor
108-9300B
Alongside the StormX, the bundle includes 2.5 m A and B looms, a CAN Lambda wideband controller with a Bosch LSU 4.9 sensor, a Link 4 bar MAP sensor and an intake air temperature (IAT) sensor with a 1/8" NPT thread.
The CAN Lambda is essential for modern tuning, giving you fast and accurate live Lambda without using up any DI or An Volt inputs. Each sensor comes with its Deutsch DTM connector kit, and the 4 bar MAP sensor suits turbo or supercharged engines running up to 3.0 bar (44 psi) of boost.
Positioned between Link entry-level and premium G4X ECUs, the StormX delivers performance, flexibility and value.The StormX is the ideal solution for builds requiring expanded I/O and some advanced tuning capability, without needing the extra features that come with our premium ECUs.
Models Supported
The StormX can control up to 4 rotors or 8 cylinders with sequential injection and direct spark.
109-9300B
Alongside the XtremeX, the bundle includes 2.5 m A and B looms, a CAN Lambda wideband controller with a Bosch LSU 4.9 sensor, a Link 4 bar MAP sensor and an intake air temperature (IAT) sensor with a 1/8" NPT thread.
The CAN Lambda is essential for modern tuning, giving you fast and accurate live Lambda without using up any DI or An Volt inputs. Each sensor comes with its Deutsch DTM connector kit, and the 4 bar MAP sensor suits turbo or supercharged engines running up to 3.0 bar (44 psi) of boost.
A premium G4X ECU for up to 8 cylinders, the XtremeX delivers extensive I/O, E-Throttle control and the full suite of G4X motorsport features for demanding performance and race applications.
Models Supported
The XtremeX can control up to 4 rotors or 8 cylinders with sequential injection and direct spark.
122-9300B
Alongside the FuryX, the bundle includes 2.5 m A and B looms, a Bosch LSU 4.9 wideband Lambda sensor, a Link 4 bar MAP sensor and an intake air temperature (IAT) sensor with a 1/8" NPT thread.
With the FuryX onboard Digital Wideband Lambda Control, the LSU 4.9 wires straight into the ECU, giving you fast and accurate live Lambda with no external controller needed. The MAP and IAT sensors each come with their Deutsch DTM connector kit, and the LSU 4.9 comes with its plug and pin kit. The 4 bar MAP sensor suits turbo or supercharged engines running up to 3.0 bar (44 psi) of boost.
The FuryX is the ideal solution for high-performance street and motorsport builds that demand flexibility, onboard Wideband Lambda, E-throttle control, extensive I/O and the advanced features of a premium G4X ECU.
Models Supported
The FuryX can control up to 3 rotors or 6 cylinders with sequential injection and direct spark.
122-9800B
G4X Fury Motorsport Bundle. Everything you need to get started wiring a Link G4X FuryX into your chosen beast!
This is the ideal package for engines with up to six cylinders and wanting to run onboard digital wideband lambda control.
G4X FuryX - A premium ECU with Onboard Digital Wideband.
A loom medium - 2.5 m long 'A' loom to suit G4X (FuryX)
B loom medium - 2.5 m long 'B' loom to suit G4X (FuryX)
Air Temperature Sensor
Coolant Temperature Sensor
Pressure sensor - for oil or fuel pressure up to 10 bar
Combined pressure and temperature sensor
156-9300B
Alongside the G5 Voodoo Neo 6, the bundle includes 2.5 m A and B looms, a Bosch LSU 4.9 wideband Lambda sensor, a Link 4 bar MAP sensor and an intake air temperature (IAT) sensor with a 1/8" NPT thread.
With the Neo 6 onboard Digital Wideband Lambda Control, the LSU 4.9 wires straight into the ECU, giving you fast and accurate live Lambda with no external controller needed. The MAP and IAT sensors each come with their Deutsch DTM connector kit, and the LSU 4.9 comes with its plug and pin kit. The 4 bar MAP sensor suits turbo or supercharged engines running up to 3.0 bar (44 psi) of boost.
Compatibility
The G5 Voodoo Neo 6 can run: 8 cylinders sequential port or direct injection and direct spark, or 6 cylinders with direct/port staged injection, and direct spark.
The G5 Voodoo Neo 6 is ideal for modern high-performance 6 or 8 cylinder builds requiring the next-generation of engine management technology.
154-9300B
Alongside the G5 Voodoo Neo 4, the bundle includes 2.5 m A and B looms, a Bosch LSU 4.9 wideband Lambda sensor, a Link 4 bar MAP sensor and an intake air temperature (IAT) sensor with a 1/8" NPT thread.
With the Neo 4 onboard Digital Wideband Lambda Control, the LSU 4.9 wires straight into the ECU, giving you fast and accurate live Lambda with no external controller needed. The MAP and IAT sensors each come with their Deutsch DTM connector kit, and the LSU 4.9 comes with its plug and pin kit. The 4 bar MAP sensor suits turbo or supercharged engines running up to 3.0 bar (44 psi) of boost.
Models Supported
The G5 Voodoo Neo 4 can run: 6 cylinders sequential port or direct injection and direct spark, or 4 cylinders with direct/port staged injection, and direct spark.
SKU 144-5000
Discover the next evolution in engine tuning with our advanced Direct Injection (DI) control module. The DI Driver-4 is a highly configurable, cost effective and integrated solution, designed to give you full control of most modern solenoid type direct injectors and high-pressure fuel pumps.
Each DI Driver-4 module can allow up to four high voltage peak and hold solenoid Direct Injectors and one high pressure peak and hold Fuel Pump to flow up to their maximum amount of fuel at a very high engine RPM.
When combined with a G5 Voodoo Pro ECU, up to three DI Driver-4 modules can be connected together to control up to 12 Direct Injectors and two independent High Pressure Fuel Pumps. Together the G5 Voodoo Pro ECU and DI Driver-4 modules can control both Direct Injection and staged Port Injection on a single tune, giving you the ultimate all-in-one solution to achieve greater power and efficiency.
Connecting to your ECU and other DI Driver-4 modules is easy thanks to CAN Bus compatibility. Set-up has been simplified with our easy-to-use free DI Link software, which is highly user configurable over USB.
Housed in a durable, sealed CNC enclosure with a waterproof Superseal automotive connector, it’s engineered to withstand demanding conditions.
All this is backed by the industry-leading reliability and support you’ve come to expect from LinkECU.
Features
Four Direct Injection Injector Drives
• One High Pressure Fuel Pump Drive
• Water Resistant, -40 to 80 °C Operating Temperature
• 1 x CAN bus with software configurable termination
• 1 x USB Type-C for configuration via DI Link software (free download, Windows only)
• Sealed CNC billet aluminium enclosure
• 26-Way waterproof Superseal automotive connector
• Uses the Super Seal D plug
• Compatible with a wide range of engine management systems, and solenoid direct injectors. (Does not support Piezo Direct Injectors)
• Max Boost Current: 17.9A, Max Boost Voltage: 65V
• Max Peak Current: 17.9A, Max Peak Duration: 2000uS
• Max Hold Current: 5.0A, Max Hold Curation: 164mS
• Max engine RPM running a Bosch HDEV: 14,200RPM
SKU 156-5000
The next generation of engine management for many more engines.
The G5 Voodoo Neo 6 can run:
8 cylinders with port or direct injection and direct spark,
6 cylinders with direct/port staged injection and direct spark
The G5 Voodoo processing units are the perfect choice for professional-level motorsport.
Inputs/Outputs
Control up to 8 cylinders with port or direct injection and direct spark, or 6 cylinders with direct/port staged injection, thanks to:
12 injector pins
8 ignition pins
6 aux. output pins
(4 injector pins are shared with 4 DI Pins. You can only use each pin for either Injection or DI, not both at the same time.)
6 ADIO pins
Highly customisable IO, using 2 types of multi purpose pins: ADIO pins and Injector/Digital-Input pins. These pins can act as inputs or outputs.
ADIO are a unique pin type. ADIO can act as an Aux Output (switched or PWM), as an Analogue Input, or as a Digital Input, but cannot read PWM/frequency.
Neo 6 has Inj/DI pins which are used as either an injector pin, Aux or a Digital Input pin. They can read PWM/frequency.
Any unused injector/ignition pins can be used as an auxiliary pin.
All ignition and auxiliary pins are back feed protected.
3 analog inputs
10 digital inputs
4 temperature inputs
2 knock inputs
2 trigger inputs
1 x wideband lambda controller
Dual H-Bridge e-throttle control
Dedicated ignition switch pin
5v sensor supply
CAN 1 via Weipu connector. CAN connector now supplies power and ground.
Communications
USB-C (cable included)
Power over USB
WiFi: Connect directly to the ECU via built-in Wifi Access Point, or add it to an existing network (antenna included)
CAN: New WEIPU connector supplies power for CAN devices
Ethernet: Built in ethernet which can function like USB. Also adds the ability to connect to the ECU over a network.
GPS: Functional when GPS antenna connected (antenna included)
Data Logging
1gb logging capacity, over WiFi, 100kHz max. total logging rate, 250 logging channels
SKU 154-5000
The next generation of engine management for many more engines.
The G5 Voodoo Neo 4 can run:
6 cylinders port or direct injection and direct spark, or,
4 cylinders with direct/port staged injection, and direct spark
The G5 Voodoo processing units are the perfect choice for professional level motorsport.
Inputs/Outputs
Control up to 6 cylinders with port or direct injection and direct spark, or 4 cylinders with direct/port staged injection, thanks to:
8 injector pins
6 ignition pins
12 aux. output pins
(4 Aux pins are shared with 4 DI Pins. You can only use each pin for either Injection or DI, not both at the same time.)
6 ADIO pins
Highly customisable IO, using 2 types of multi purpose pins: ADIO pins and Aux./Digital-Input pins. These pins can act as inputs or outputs.
ADIO are a unique pin type. ADIO can act as an Aux Output (switched or PWM), as an Analogue Input, or as a Digital Input, but cannot read PWM/frequency.
Neo 4 has Aux/DI pins which are used as either an Aux pin, or a Digital Input pin. They can read PWM/frequency.
Any unused injector/ignition pins can be used as an auxiliary pin
All ignition and auxiliary pins are back feed protected.
3 analog inputs
10 digital inputs
4 temperature inputs
2 knock inputs
2 trigger inputs
1 x wideband lambda controller
Dual H-Bridge e-throttle control
Dedicated ignition switch pin
5v sensor supply
CAN 1 via Weipu connector. CAN connector now supplies power and ground.
Communications
USB-C (cable included)
Power over USB
WiFi: Connect directly to the ECU via built-in Wifi Access Point, or add it to an existing network (antenna included)
CAN: New WEIPU connector supplies power for CAN devices
Ethernet: Built in ethernet which can function like USB. Also adds the ability to connect to the ECU over a network.
GPS: Functional when GPS antenna connected (antenna included)
SKU 110-0005
Mounting bracket for G4+ & G4X Atom & Monsoon (MTB2)
SKU 100-0113
Mounting bracket for G4+ & G4X Fury, Xtreme, Storm, Force (MTB1)
SKU 135-9300B
Triple Bundle - Includes 3 x Razor PDMs.
Link's highly anticipated PDM, the Razor PDM, is an intelligent Power Distribution Module that replaces traditional fuses and relays, putting you in complete control of your setup.
The Razor PDM is a programmable device that uses logic for the smart control of any outputs you have connected, meaning events and commands can be triggered when your vehicle hits specific parameters.
The device will allow you to manage things such as fuel pumps, radiator fans, electronic throttles, servos, lights and more, as well as monitoring analog or digital sensor signals.
You can gain full control by using an Analog Switch Panel, CAN Keypad or ECU to switch output channels, as well as increasing reliability and protecting your critical components from damage.
With superior thermal performance, the Razor PDM has been designed with vehicle protection in mind, while allowing for a more efficient, cleaner, and reliable build.
It may be small and compact, but the Razor PDM can handle up to 100 Amps of continuous combined current, as well as 160A of non-repetitive maximum current. If you need to manage even more power, you can easily add multiple Razor PDM’s via CAN or use as a CAN Expander to increase your inputs and outputs.
The Razor PDM has the ability to connect with many other ECU brands and CAN devices when using a custom CAN stream. Those of you with a Link ECU will be pleased to know that our software comes with a pre-configured stream, so your Link products will work with the device straight out of the box.
Setup and management of the Razor PDM is performed through our custom PDM Link software, which is free to download and use.
In the box:
• Link Razor PDM
• Mounting plate and screws
• Superseal C Plug and Pin Kit
• USB-C connection cable
• Positive terminal insulation boot
• 2 x high-current ring terminals and bolts
• Quickstart guide
SKU 135-9200B
Bundle - Includes 2 x Razor PDMs.
Link's highly anticipated PDM, the Razor PDM, is an intelligent Power Distribution Module that replaces traditional fuses and relays, putting you in complete control of your setup.
The Razor PDM is a programmable device that uses logic for the smart control of any outputs you have connected, meaning events and commands can be triggered when your vehicle hits specific parameters.
The device will allow you to manage things such as fuel pumps, radiator fans, electronic throttles, servos, lights and more, as well as monitoring analog or digital sensor signals.
You can gain full control by using an Analog Switch Panel, CAN Keypad or ECU to switch output channels, as well as increasing reliability and protecting your critical components from damage.
With superior thermal performance, the Razor PDM has been designed with vehicle protection in mind, while allowing for a more efficient, cleaner, and reliable build.
It may be small and compact, but the Razor PDM can handle up to 100 Amps of continuous combined current, as well as 160A of non-repetitive maximum current. If you need to manage even more power, you can easily add multiple Razor PDM’s via CAN or use as a CAN Expander to increase your inputs and outputs.
The Razor PDM has the ability to connect with many other ECU brands and CAN devices when using a custom CAN stream. Those of you with a Link ECU will be pleased to know that our software comes with a pre-configured stream, so your Link products will work with the device straight out of the box.
Setup and management of the Razor PDM is performed through our custom PDM Link software, which is free to download and use.
In the box:
• Link Razor PDM
• Mounting plate and screws
• Superseal C Plug and Pin Kit
• USB-C connection cable
• Positive terminal insulation boot
• 2 x high-current ring terminals and bolts
• Quickstart guide
SKU 135-1000
Link's highly anticipated PDM, the Razor PDM, is an intelligent Power Distribution Module that replaces traditional fuses and relays, putting you in complete control of your setup.
The Razor PDM is a programmable device that uses logic for the smart control of any outputs you have connected, meaning events and commands can be triggered when your vehicle hits specific parameters.
The device will allow you to manage things such as fuel pumps, radiator fans, electronic throttles, servos, lights and more, as well as monitoring analog or digital sensor signals.
You can gain full control by using an Analog Switch Panel, CAN Keypad or ECU to switch output channels, as well as increasing reliability and protecting your critical components from damage.
With superior thermal performance, the Razor PDM has been designed with vehicle protection in mind, while allowing for a more efficient, cleaner, and reliable build.
It may be small and compact, but the Razor PDM can handle up to 100 Amps of continuous combined current, as well as 160A of non-repetitive maximum current. If you need to manage even more power, you can easily add multiple Razor PDM’s via CAN or use as a CAN Expander to increase your inputs and outputs.
The Razor PDM has the ability to connect with many other ECU brands and CAN devices when using a custom CAN stream. Those of you with a Link ECU will be pleased to know that our software comes with a pre-configured stream, so your Link products will work with the device straight out of the box.
Setup and management of the Razor PDM is performed through our custom PDM Link software, which is free to download and use.
In the box:
• Link Razor PDM
• Mounting plate and screws
• Superseal C Plug and Pin Kit
• USB-C connection cable
• Positive terminal insulation boot
• 2 x high-current ring terminals and bolts
• Quickstart guide
SKU 101-0002
0.4m long 'A' loom to suit G4, G4+ and G4X Wire-In ECUs
Perfect for all custom wiring jobs utilising Link WireIn ECUs. The ‘A’ Loom has a Link ‘A’ ECU connector at one end and unterminated wires at the other. All wires are colour coded to match the manual. This loom is also available in 2.5m and 5m lengths.
Suitable for:
All Link G4X WireIn ECU’s (Note: Loom B will also be required for the Storm/Fury/Xtreme)
Link G4+ Atom (NB: Does NOT suit the earlier G4 Atom models. I.e. G4+ only)
Link G4+ Atom II
Link G4+ Monsoon
Link G4 Storm
Link G4+ Storm Blue
Link G4+ Storm Black (Note: Loom B will also be required)
Link G4 RX
Link G4+ Fury (Note: Loom B will also be required)
Link G4 Xtreme (Note: Loom B will also be required)
Link G4+ Xtreme (Note: Loom B will also be required)
Link G4+ Thunder (Note: Loom B and connector kits C and D may also be required)
Vipec V44
Vipec i44
Vipec V88 (Note: Loom B will also be required)
Vipec i88 (Note: Loom B will also be required)
SKU 101-0003
0.4m long 'B' loom to suit G4, G4+ and G4X Wire-In ECUs
Perfect for all custom wiring jobs utilising Link WireIn ECUs. The ‘B’ Loom has a Link ‘B’ ECU connector at one end and unterminated wires at the other. All wires are colour coded to match the manual. This loom is also available in 2.5m and 5m lengths.
Suitable for:
Link G4X Storm (Loom A also required)
Link G4X and G4+ Fury (Loom A also required)
Link G4X, G4+ and G4 Xtreme (Loom A also required)
Link G4+ Thunder (Note: Loom A and connector kits C and D may also be required)
Link G4+ Storm Black (Loom A also required) – Note: Loom B is not required for the older Silver or Blue G4 or G4+ Storm models
Vipec V88 (Loom A also required)
Vipec i88 (Loom A also required)
SKU 101-0005
2.5 m long 'A' loom to suit G4, G4+ and G4X ECUs
Perfect for all custom wiring jobs utilising Link WireIn ECUs. The ‘A’ Loom has a Link ‘A’ ECU connector at one end and unterminated wires at the other. All wires are colour coded to match the manual. This loom is also available in 0.4m and 5m lengths.
Added features of 2.5m and 5m ‘A’ Looms include:
-Shielded Dual Core wires for trigger signals
-Added ground and 5V wires spliced in with labels suggesting pin use
Suitable for:
All Link G4X WireIn ECU’s (Note: Loom B will also be required for the Storm/Fury/Xtreme)
Link G4+ Thunder (Note: Loom B and connector kits C and D may also be required)
Link G4+ Atom (NB: Does NOT suit the earlier G4 Atom models. I.e. G4+ only)
Link G4+ Atom II
Link G4+ Monsoon
Link G4 Storm
Link G4+ Storm Blue
Link G4+ Storm Black (Note: Loom B will also be required)
Link G4 RX
Link G4+ Fury (Note: Loom B will also be required)
Link G4 Xtreme (Note: Loom B will also be required)
Link G4+ Xtreme (Note: Loom B will also be required)
Vipec V44
Vipec i44
Vipec V88 (Note: Loom B will also be required)
Vipec i88 (Note: Loom B will also be required)
SKU 101-0006
2.5 m long 'B' loom to suit G4, G4+ and G4X ECUs
Perfect for all custom wiring jobs utilising Link WireIn ECUs. The ‘B’ Loom has a Link ‘B’ ECU connector at one end and unterminated wires at the other. All wires are colour coded to match the manual. This loom is also available in 0.4m and 5m lengths.
Added features of 2.5m and 5m ‘B’ Looms include:
-Shielded Dual Core wires for knock signals
Suitable for:
Link G4X Storm (Loom A also required)
Link G4X and G4+ Fury (Loom A also required)
Link G4X, G4+ and G4 Xtreme (Loom A also required)
Link G4+ Thunder (Note: Loom A and connector kits C and D may also be required)
Link G4+ Storm Black (Loom A also required) – Note: Loom B is not required for the older Silver or Blue G4 or G4+ Storm models
Vipec V88 (Loom A also required)
Vipec i88 (Loom A also required)
SKU 101-0008
5 m long 'A' loom to suit G4, G4+ and G4X ECUs
Perfect for all custom wiring jobs utilising Link WireIn ECUs. The ‘A’ Loom has a Link ‘A’ ECU connector at one end and unterminated wires at the other. All wires are colour coded to match the manual. This loom is also available in 0.4m and 2.5m lengths.
Added features of 2.5m and 5m ‘A’ Looms include:
- Shielded Dual Core wires for trigger signals
- Added ground and 5V wires spliced in with labels suggesting pin use
Suitable for:
All Link G4X WireIn ECU’s (Note: Loom B will also be required for the Storm/Fury/Xtreme)
Link G4+ Atom (NB: Does NOT suit the earlier G4 Atom models. I.e. G4+ only)
Link G4+ Atom II
Link G4+ Monsoon
Link G4 Storm
Link G4+ Storm Blue
Link G4+ Storm Black (Note: Loom B will also be required)
Link G4 RX
Link G4+ Fury (Note: Loom B will also be required)
Link G4 Xtreme (Note: Loom B will also be required)
Link G4+ Xtreme (Note: Loom B will also be required)
Link G4+ Thunder (Note: Loom B and connector kits C and D may also be required)
Vipec V44
Vipec i44
Vipec V88 (Note: Loom B will also be required)
Vipec i88 (Note: Loom B will also be required)
SKU 101-0009
5 m long 'B' loom to suit G4, G4+ and G4X ECUs
Perfect for all custom wiring jobs utilising Link WireIn ECUs. The ‘B’ Loom has a Link ‘B’ ECU connector at one end and unterminated wires at the other. All wires are colour coded to match the manual. This loom is also available in 0.4m and 2.5m lengths.
Added features of 2.5m and 5m ‘B’ Looms include:
-Shielded Dual Core wires for knock signals
Suitable for:
Link G4X Storm (Loom A also required)
Link G4X and G4+ Fury (Loom A also required)
Link G4X, G4+ and G4 Xtreme (Loom A also required)
Link G4+ Thunder (Note: Loom A and connector kits C and D may also be required)
Link G4+ Storm Black (Loom A also required) – Note: Loom B is not required for the older Silver or Blue G4 or G4+ Storm models
Vipec V88 (Loom A also required)
Vipec i88 (Loom A also required)
SKU 152-5000
New G5 Voodoo Pro
(ECU used in our race program)
G5 Voodoo Pro puts real magic in your hands and opens a new world of possibilities with the ability to control port plus direct injection, more injector and ignition drives, advanced communications and many more features.
With 12 Injection, 8 Ignition and 4 multi-purpose (inj, ign, aux) drives (24 total) the G5 Voodoo Pro can run up to:
· 12 cylinders port or direct injection and direct spark, or
· 8 cylinders with direct/port staged injection and direct spark.
The supported cylinder count depends on the type and number of fuel pumps used.
For more information please see the Features and Specifications tab or view our Product Introduction page here.
The G5 Voodoo Pro works on a variety of vehicles, please contact Technical Support for advice regarding your specific project.
Click here to head to the Knowledge Base for more technical information (includes downloads for the Quick Start Guide and I/O table).
In the box: G5 Voodoo Pro ECU, USB-C Connection Cable, Wi-Fi Antenna, 4m GPS Antenna (Magnetic or Adhesive Mount), USB-C and SMA Dust Covers, QuickStart Guide (A5), Installer I/O table (A3), Mounting Screws, Link stickers
Features and Specifications
· Built-in Wi-Fi, with real-time PC Link connection
· Built-in Global Positioning System (GPS) up to 50Hz
· Built-in Ethernet, the fastest and most stable way to view or download data logs, calibrate and tune your ECU.
· Highly customisable IO, now using eight ADIO pins.
· Dual onboard LSU 4.9 digital wideband controllers.
· Dual on-board H-Bridges that support things like E-Throttle (Drive by Wire) and low power E-Wastegates.
· 1GB onboard of data logging memory.
· All G4X and G5 tunes are compatible with the G5 Voodoo Pro.
· CNC Case, Sealed enclosure
Outputs
· 12 injector drives
· 8 ignition drives
· 4 injector/ignition dual role drives
· 6 auxiliary Outputs
· +5V sensor power supply
· Any unused injector/ignition pins can be used as an auxiliary pin
· All ignition and auxiliary pins are fly back protected.
Inputs
· 10 digital inputs
· 4 temperature inputs
· 14 analogue inputs
· 2 trigger inputs
· 2 knock inputs
Input/Outputs
· 8 ADIO dual purpose pins
Communications
· USB-C (cable included)
· Connect directly to the ECU via built-in Wi-Fi Access Point, or add it to an existing network (Antenna Included)
· Dual CAN (CAN 1 on CAN connector, CAN 2 on header E)
· GPS (antenna included)
· Ethernet with daisy chain support
Size & Weight
· Depth: 109.2 mm (4.3 inches)
· Width: 193.5 mm (7.6 inches)
· Max height: 45.0 mm (1.8 inches)
· Weight: 768g (27 ounces)
Connectivity
The G5 Voodoo Pro supports the following comms standards:
· USB-C
· Wi-Fi
· CAN
· GPS
· Ethernet
The G5 Voodoo Pro uses A, B & E Superseal headers. A & B headers are closely matched pinouts with the G4X and G5 Voodoo Neo platforms.
It is now possible to connect to your ECU using a standard USB-C cable, or alternatively by using Wi-Fi or Ethernet.
GPS connectivity can be initialised by simply adding a GPS antenna.
SKU 122-4000
A premium ECU with Onboard Digital Wideband.
The FuryX is a premium ECU like the XtremeX, but with added Onboard Digital Wideband Lambda Control.
Now on the G4X platform, the FuryX features a faster processor, faster communications & a huge 512 megabytes of data logging!
With 8 injector drives and 6 ignition drives, the FuryX can control up to 3 rotors or 6 cylinders with sequential injection and direct spark, making it an excellent choice for professional level motorsport or more demanding road car applications.
The added benefit of a Onboard Digital Wideband Lambda Controller means higher accuracy of the unit, plus a simple setup.
The FuryX comes supplied with stickers, a quickstart guide, a mounting bracket and a USB tuning cable.
Requires 'A' & 'B' Looms or 'A' & 'B' Pin Kits, not supplied.
See the additional info for a full list of specifications.
SPEC OVERVIEW:
Inputs
8/10* x Digital inputs
4 x Temperature inputs
9 x Analog inputs
2 x Trigger inputs
2 x Knock inputs
1 x LSU 4.9 Wideband lambda sensor input
Outputs
8 x Injection drives
6 x Ignition drivers
10 x Auxiliary outputs^
+5V Sensor power supply
+8V Sensor power supply
^unused fuel and ignition drives can be used as additional Aux outputs
Communications
2* x CAN bus
1x Serial (RS232) connection
1x USB tuning connection
Physical
Dimensions: 185mm(L) x 130mm(W) x 40mm(H) (without looms)
Mass: 680grams
*DI 9 & 10 pins used by second CAN Bus
What's in the box?
Supplied with USB tuning cable and mounting bracket.
Requires “A” & “B” looms or “A” & “B” connector kits (not supplied).
If you are after more inputs, outputs or features, consider the G5 Voodoo Pro
SKU 109-4000
The XtremeX is one of Link’s premium ECU’s with more inputs, outputs and features.
The XtremeX has built in E-throttle and all the advanced features including Anti-lag, Cruise Control and Traction Control.
With 8 Injector drives and 8 ignition drives the XtremeX can control up to 4 rotors or 8 cylinders with sequential injection and direct spark. The XtremeX is a great choice for professional level motorsport or more demanding road car applications.
Please note: for peak & hold please contact a Link ECU Sales Person to purchase a G4+ Xtreme ECU.
Requires "A" & "B" Looms for installation.
Inputs
8/10* x Digital inputs
4 x Temperature inputs
11 x Analog inputs
2 x Trigger inputs
2 x Knock inputs
*2 inputs required when using 2nd CAN Bus
Outputs
8 x injection drives
8 x Ignition drivers
10 x Auxiliary outputs^
+5V Sensor power supply
+8V Sensor power supply
^unused fuel and ignition drives can be used as additional Aux outputs
Communications
2* x CAN bus
1x Serial (RS232) connection
1x USB tuning connection
Faster communications than G4+ models
512 Megabytes Data Logging
Physical
Dimensions: 185mm(L) x 130mm(W) x 40mm(H) (without looms)
Mass: 680grams
Advanced features not found on the Storm:
Fully programmable E-throttle control complete with capability of gear shift throttle blip and antilag.
Cruise control.
Two independent CAN modules.
30 general purpose tables (up from 20)
All Motorsport features including full gear shift control, cruise control, traction control, antilag and launch control.
Advanced closed loop lambda strategy and dual bank lambda control.
What's in the box?
Supplied with USB tuning cable and mounting bracket.
*Requires “A” & “B” looms or “A” & “B” connector kits, sold separately.
If it is Onboard Digital Wideband Lambda Control you are after, consider the Fury.
SKU 108-4000
Advanced tuning features at an affordable price.
The Link G4X StormX ECU is the latest version of our trusty, mid-sized ECU. With eight injector and eight ignition drives, it allows sequential injection and direct spark on engines with up to eight cylinders or four rotors.
The StormX has all the upgrades of the AtomX and MonsoonX but offers more advanced tuning features like a built in Trigger Oscilloscope, Stepper Motor Idle Control, Rotary Oil Metering Pump Control, Onboard Knock Control, Open and Closed Loop Boost Control plus most Motorsport features including Full Gear Shift Control, Antilag and Launch Control.
The StormX has expanded data logging and is more responsive with a higher bandwidth than its G4+ Storm predecessor. G4X features 512 megabytes of logging at 32bit using up to 250 channels, each limited to up to 1kHz per channel (by the Operating System), with a maximum of 100 kSamples/sec.
Inputs
8 x Digital inputs
3 x Temperature inputs
8 x Analog inputs
2 x Trigger Inputs
2 x Knock Inputs
Outputs
8 x Injection drives
8 x Ignition drivers
8 x Auxiliary outputs^
+5V Sensor power supply
+8V Sensor power supply
^unused fuel and ignition drives can be used as additional Aux outputs
Communications
1 x CAN bus
1 x USB tuning connection
Upgraded communications chip (at least 8 x faster than G4+ V2)
Advanced features not found on the smaller Link ECUs (AtomX and MonsoonX):
Built in trigger oscilloscope.
Onboard Knock Control – support for two knock sensors wired directly to the ECU. No external amplifier required.
Boost control can be open or closed loop with up to three switchable tables.
Idle valve solenoid or stepper motor control.
Rotary oil metering pump control.
Most Motorsport features including full gear shift control, antilag and launch control
Up to 4 fully variable closed loop VVT cams.
*Requires “A” & “B” looms or “A” & “B” connector kits.
*Is it Traction control, peak and hold injection or e-throttle? Consider the Xtreme or Fury ECUs.
It also features 8 x faster communications speed, allowing you to download logs 8 x faster and pushes all the logging quickly up to a new and improved PCLink – available for download below in additional info
SKU 127-4000
MonsoonX
More features, more powerful.
The MonsoonX will control up to 2 rotors or 4 cylinders with sequential injection and direct spark. Or, it can be used for up to eight cylinders using batch fire.
This makes it ideal for naturally aspirated or turbocharged engines that just need a retune and one or two extra features, so you don’t need to jump up to one of our higher-level ECUs.
The MonsoonX processing unit has been upgraded to provide 512 megabytes of data logging, meaning you can log much more data at a faster sample rate. Control loops are also more precise compared to its G4+ predecessor, along with advancements such as single precision floating point format fuel tables, better resolution within ignition timing and faster communications. These upgrades make the G4X Monsoon a true powerhouse in a small shell.
The G4X logging features 512 megabytes at 32bit using up to 250 channels, each limited to up to 1kHz per channel (by the Operating System), with a maximum of 100 kSamples/sec.
With the MonsoonX you have all the tuning capabilities of the AtomX, but you can also choose to run some of the following features: Launch Control, Anti-lag, VVT Control and Closed Loop Boost Control. It also comes with a built in 4 bar or 7 bar MAP sensor further reducing installation cost. Now featuring Knock Control.
Note: The MonsoonX will run any of the above features, but it cannot run them all at once. The number of features you can run is dependent on how many of the limited Inputs and Outputs each feature needs.
The MonsoonX is an Automotive Control Unit.
Requires A Loom.
The MonsoonX is ideal for:
1-12 Cylinder Distributed
2-8 Cylinder Wasted Spark
1-4 Cylinder Direct Spark
Odd Fire Engines
2-Stroke Engines
Configurable Firing Order
Configurable TDC Points (for odd fire)
Inputs
4 x Digital inputs
2 x Temperature inputs
4 x Analog inputs
2 x Trigger inputs
1 x Knock Input (Shared with DI4)
1 x Onboard 4 Bar MAP sensor
Outputs
4 x Injector drives
4 x Ignition drivers
6 x Auxiliary outputs^
+5V Sensor power supply
^unused ignition drives can be used as additional Aux outputs
Communications
1x CAN bus
1x USB tuning connection
Upgraded communications chip (four times faster than G4+)
Physical:
Dimensions: 95mm(L) x 130mm(W) x 45mm(H) (without loom)
Weight: 220 grams
Advanced features not found on the AtomX:
Antilag, rolling antilag and launch control.
Up to 2 fully variable closed loop VVT cams.
Misc:
512MB of logging memory within data storage unit
20 general purpose tables
Runs on PC Link software for G4X
The MonsoonX comes supplied with waterproof connectors, a mounting bracket and a USB tuning cable. “A Loom” to be purchased separately.
SKU 111-4000
AtomX
Small, but mighty!
The AtomX can control up to 2 rotors or 4 cylinders with sequential injection and direct spark. Or, it can be used for up to eight cylinders using batch fire. Now featuring Knock Control.
This makes it ideal for naturally aspirated engines that just need a re-tune and don't need all the extra sensors and features that come with our higher level ECUs.
The Link G4X AtomX ECU may be our entry-level ECU but don't let its size fool you. The AtomX has expanded data logging and uses the same microcontroller as the entire G4X range! The processing unit is more responsive and has higher bandwidth than its G4+ Atom II predecessor.
G4X features 512 megabytes of logging at 32bit using up to 250 channels, each limited to up to 1kHz per channel (by the Operating System), with a maximum of 100 kSamples/sec.
G4X features 8 x faster communications speed than G4+ ECUs, allowing you to download logs 8 x faster and pushes all the logging quickly up to a new and improved PCLink – available for download below in the features tab.
The AtomX is an automotive control unit.
Requires "A" loom.
The AtomX is ideal for:
1-12 Cylinder Distributed
2-8 Cylinder Wasted Spark
1-4 Cylinder Direct Spark
Odd Fire Engines
2-Stroke Engines
Configurable Firing Order
Configurable TDC Points (for odd fire)
Communications:1x CAN bus
1x USB tuning connection
1 x thirty four pin, waterproof connector
Upgraded Communications Chip
Misc:
Comes loaded with all of Link ECU's standard features.
512MB of logging memory within data storage unit
20 general purpose tables
Runs on PC Link software for G4X
Physical:
Dimensions: 90mmL x 130mmW x 45mmH (without loom)
Weight: 180 grams
What's in the box:
The AtomX ECU is supplied with a USB tuning cable, mounting bracket and four Link ECU stickers.
SKU 101-0211
Required to add CAN communication to WireIn ECU's which have CAN accessible via the 6Pin round CAN connector on the front of the ECU.
Compatible ECU's:
G5 Voodoo Pro (CAN1)
G4X/G4+ Xtreme (CAN1)
G4X/G4+ Fury (CAN1)
G4+ Force (CAN1)
G4+ Thunder (CAN1)
Specs
DTM4 Male to LTW 6Pin. 12V & GND Flying Leads. CAN Loom Length 300mm (Flying lead length 500mm)
DTM4 Pin Out
Pin 4: CAN H
Pin 3: CAN L
Pin 2: Ground
Pin 1: 12V
SKU 101-0212
CAN Splitter Cable for connecting an additional CAN devices.
Use to connect from a CANJST, CANLTW or CANSS into 2 CAN devices.
Specs
DTM4 Female to 2 x DTM4 Male. Includes CAN and Power Wiring.
Loom 1 Length: 80mm
Loom 2 Length: 120mm
DTM4 Pin Out
Pin 4: CAN H
Pin 3: CAN L
Pin 2: Ground
Pin 1: 12V
No results found
No results match your search. Try removing a few filters.
Special Order Parts
Parts Available but will need sales representative assistance.
Special shipping/part fitment
Click HERE or on any image to request a quote for any part you do not see on the website.
We will be adding more parts to the website daily so check back for new inventory.