G4X Plugin ECU - S13Link - NS13X - 76 pin

$2,325.00

SKU 216-4000

Designed for the SR20 and CA18 engines, that use the 76 pin Blue ECU Header.  

DOUBLE CHECK PINOUT

Suitable applications:  
Nissan S13 CA18DET 
Nissan 180SX CA18DET   
Nissan S14 (pre facelift) SR20DET

Easy to install. Affordable. Reliable.  
G4X PlugIn ECUs offer the latest in engine management technology, designed to easily maximize the potential from your car.  
This ECU fits inside the factory OEM enclosure. Installation is a breeze, with no alteration of the factory wiring loom required for the models listed below. 

Designed for the SR20 and CA18 engines, that use the 76 pin Blue ECU Header.  

  • Please check your connector matches the header in the listed photo before purchasing.  

  • This ECU works for manual transmissions only.  

  • It includes an onboard 4 bar or 7 bar MAP sensor. 

  • Most factory features are supported. 

  • Check the features tab for I/O expansion options. 

  • This ECU will need a modification before E-Throttle is usable.

Click here to download the user manual.

SKU 216-4000

Designed for the SR20 and CA18 engines, that use the 76 pin Blue ECU Header.  

DOUBLE CHECK PINOUT

Suitable applications:  
Nissan S13 CA18DET 
Nissan 180SX CA18DET   
Nissan S14 (pre facelift) SR20DET

Easy to install. Affordable. Reliable.  
G4X PlugIn ECUs offer the latest in engine management technology, designed to easily maximize the potential from your car.  
This ECU fits inside the factory OEM enclosure. Installation is a breeze, with no alteration of the factory wiring loom required for the models listed below. 

Designed for the SR20 and CA18 engines, that use the 76 pin Blue ECU Header.  

  • Please check your connector matches the header in the listed photo before purchasing.  

  • This ECU works for manual transmissions only.  

  • It includes an onboard 4 bar or 7 bar MAP sensor. 

  • Most factory features are supported. 

  • Check the features tab for I/O expansion options. 

  • This ECU will need a modification before E-Throttle is usable.

Click here to download the user manual.

Link Engine Management products are not recommended where installation and tuning of such products contravenes your countries laws or interferes with the vehicle safety or pollution protection features. For track/race purposes only.

G4X PlugIn Key Features (where applicable):
Up to 6D fuel and ignition mappingPrecision closed loop cam control (four cam, independent control)Sequential fuel deliveryDigital triggering, all OEM patternsOEM idle hardware supported5D boost control with three switchable tablesMotorsport features - antilag, launch, flat shiftContinuous barometric correction (on board)CAN portQuickTune - automated fuel tuningIndividual cylinder correctionUSB tuning cable includedStats recording into on-board memoryGear compensations for spark, boost and fuelReal time selectable dual fuel, ignition and boost mapsSync and crank sensors can be a combination of Hall effect, variable reluctance or opticalBoost control referenced to gear, speed or throttle position512 mega bytes data logging memoryStaged injectionKnock with "windowing"

I/O Expansion Options:
The following expansion connector inputs/outputs are provided: 
Expansion Connector 1 
Gnd                Sensor Ground Only  
+5V Out        Low Current +5V Supply 
DI 5                Digital Input 
DI 6                Digital Input 
DI 7                Digital Input 
An Volt 6        Analog 0-5V input 
An Temp 4        Temperature sensor input 
An Temp 3        Temperature sensor input 

Expansion connector 2  
Ign 5                Ignition 5 Auxiliary Output 
Ign 6                Ignition 6 Auxiliary Output 
Ign 7                Ignition 7 Auxiliary Output 
Ign 8                Ignition 8 Auxiliary Output 
Volt 8                Analog 0-5V input 
Volt 9                Analog 0-5V input 
Volt 10                Analog 0-5V input 
Volt 11                Analog 0-5V input 

Click here for more product information